diff --git a/config/printer-flashforge-creator-pro-2018.cfg b/config/printer-flashforge-creator-pro-2018.cfg
index 1ed04313a740..43cdbc876de9 100644
--- a/config/printer-flashforge-creator-pro-2018.cfg
+++ b/config/printer-flashforge-creator-pro-2018.cfg
@@ -5,6 +5,11 @@
 # Use the following command to flash the board:
 #  avrdude -c stk500v2 -p m2560 -P /dev/serial/by-id/usb-MakerBot_Industries_The_Replicator_557373136313514061A2-if00 -b 57600 -D -U out/klipper.elf.hex
 
+# Note: 2019 models may use a different serial ID, e.g.:
+#   /dev/serial/by-id/usb-MakerBot_Industries_The_Replicator_85633323630351A090F0-if00
+# Check for yourself and update here and below accordingly.
+
+
 # See docs/Config_Reference.md for a description of parameters.
 
 [stepper_x]
@@ -16,7 +21,8 @@ rotation_distance: 34
 endstop_pin: ^!PL1
 position_endstop: 116
 position_max: 116
-position_min: -116
+# 116 + 34mm for extruder offset, so right extruder can reach left edge.
+position_min: -150
 homing_speed: 50
 
 [stepper_y]
@@ -39,9 +45,11 @@ microsteps: 16
 rotation_distance: 8
 endstop_pin: !PL6
 position_endstop: -0.25
-position_max: 181
+# Conservative maximum (-6mm from empirical max)
+position_max: 170
 position_min: -0.25
 
+# Right extruder, as defined by stock firmware
 [extruder]
 step_pin: PA3
 dir_pin: !PA2
@@ -63,6 +71,7 @@ pid_kd: 144.566
 min_temp: 0
 max_temp: 260
 
+# Left extruder, as defined by stock firmware
 [extruder1]
 step_pin: PA7
 dir_pin: PA6
@@ -97,12 +106,15 @@ gcode:
 
 [heater_fan extruder_fan]
 pin: PH4
+heater: extruder
 
 [heater_fan extruder1_fan]
 pin: PB6
+heater: extruder1
 
 [fan]
 pin: PL5
+kick_start_time: 0.5
 
 [heater_bed]
 heater_pin: PL4
@@ -115,8 +127,18 @@ pid_kd: 645.290
 min_temp: 0
 max_temp: 130
 
+[bed_screws]
+screw1: 0, -65
+screw1_name: Front Center
+screw2: -50, 65
+screw2_name: Back Left
+screw3: 50, 65
+screw3_name: Back Right
+
 [mcu]
 serial: /dev/serial/by-id/usb-MakerBot_Industries_The_Replicator_557373136313514061A2-if00
+# Note: 2019 models may use a different serial ID, e.g.:
+#   /dev/serial/by-id/usb-MakerBot_Industries_The_Replicator_85633323630351A090F0-if00
 restart_method: command
 
 [printer]
@@ -169,6 +191,12 @@ back_pin: ^PJ2
 up_pin: ^PJ4
 down_pin: ^PJ3
 
+[pwm_cycle_time beeper]
+pin: PG5
+value: 0
+shutdown_value: 0
+cycle_time: 0.001
+
 [pca9533 led_strip]
 i2c_bus: twi
 i2c_address: 98