Merge pull request #3581 from grilliiiiii/dev1

Modify: modify instructions about jumper caps on servo driver board

Author: nfs0619

docs/Sensor/SeeedStudio_XIAO/SeeedStudio_XIAO_Expansion_board/Bus_Servo_Driver_Board.md

@@ -129,7 +129,7 @@ This method is used when connecting directly to the UART pins of a microcontroll
 
 - **Jumper Setting (Critical):**
 
-  - Use a 2.54mm jumper cap to short-circuit the 2pin pin on the front of the board. (It's shorted by default)
+  - There is no need to use a 2.54mm jumper cap to short-circuit the 2pin pin on the front of the board. (It's not shorted by default)
     <div style={{textAlign:'center'}}><img src="https://files.seeedstudio.com/wiki/bus_servo_driver_board/change-2.png" style={{width:400, height:'auto'}}/></div>
 
 - **Powering the Host:** Your host device (e.g., Raspberry Pi Zero, ESP32, XIAO) will require its own separate power supply.
@@ -153,7 +153,7 @@ This method is used when connecting to a computer or single-board computer with
 
     <div style={{textAlign:'center'}}><img src="https://files.seeedstudio.com/wiki/bus_servo_driver_board/change-1.png" style={{width:400, height:'auto'}}/></div>
 
-  - **Step 2.** Use a 2.54mm jumper cap to short-circuit the 2pin pin on the front of the board. (It's shorted by default)
+  - **Step 2.** Use a 2.54mm jumper cap to short-circuit the 2pin pin on the front of the board. (It's not shorted by default)
     <div style={{textAlign:'center'}}><img src="https://files.seeedstudio.com/wiki/bus_servo_driver_board/change-2.png" style={{width:400, height:'auto'}}/></div>
 
 ### Required Components (Before You Start)

docs/zh-CN/Sensor/SeeedStudio_XIAO/SeeedStudio_XIAO_Expansion_board/cn_Bus_Servo_Driver_Board.md

@@ -129,7 +129,7 @@ import TabItem from '@theme/TabItem';
 
 - **跳线设置（关键）：**
 
-  - 使用 2.54mm 跳线帽短接板子正面的 2pin 引脚。（默认已短接）
+  - 无需使用 2.54mm 跳线帽短接板子正面的 2pin 引脚。（默认未短接）
     <div style={{textAlign:'center'}}><img src="https://files.seeedstudio.com/wiki/bus_servo_driver_board/change-2.png" style={{width:400, height:'auto'}}/></div>
 
 - **为主机供电：** 您的主机设备（如 Raspberry Pi Zero、ESP32、XIAO）需要自己的独立电源。
@@ -153,7 +153,7 @@ import TabItem from '@theme/TabItem';
 
     <div style={{textAlign:'center'}}><img src="https://files.seeedstudio.com/wiki/bus_servo_driver_board/change-1.png" style={{width:400, height:'auto'}}/></div>
 
-  - **步骤 2.** 使用 2.54mm 跳线帽短接板子正面的 2pin 引脚。（默认已短接）
+  - **步骤 2.** 使用 2.54mm 跳线帽短接板子正面的 2pin 引脚。（默认未短接）
     <div style={{textAlign:'center'}}><img src="https://files.seeedstudio.com/wiki/bus_servo_driver_board/change-2.png" style={{width:400, height:'auto'}}/></div>
 
 ### 所需组件（开始之前）