| layout | title |
|---|---|
documentation |
ZDW103 - ZWave |
{% include base.html %}
This describes the Z-Wave device ZDW103, manufactured by ACT - Advanced Control Technologies with the thing type UID of act_zdw103_00_000.
The ZDW103 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
No device information is provided in the database. Consider updating the database to improve the documentation.
The following table summarises the channels available for the ZDW103 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Dimmer | switch_dimmer | DimmableLight | Dimmer |
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.
The following table provides a summary of the 16 configuration parameters available in the ZDW103. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Set Ignore Start Level Bit When Transmitting Dim Commands | Defines the behavior when transmitting dim commands |
| 2 | Suspend Group 4 | Disable transmission of command to Group 4 |
| 3 | Night Light | Defines the behavior of the blue LED. |
| 4 | Invert Switch | Change the top of the switch to OFF and the bottom of the switch to ON. |
| 5 | Ignore Start-Level (Receiving) | This dimmer will start dimming from its current level. |
| 6 | Don’t Send Level Command After Transmitting Dim Commands | Change behavior of dim level information update |
| 7 | On/Off Command Dim Step | Indicates how many levels the dimmer will change for each dimming step. |
| 8 | On/Off Command Dim Rate | Sets the rate at which the dimmer changes the light level. |
| 9 | Local Control Dim Step | Indicates how many levels the dimmer will change for each dimming step. |
| 10 | Local Control Dim Rate | Sets the dim rate |
| 11 | ALL ON/ALL OFF Dim Step | Indicates how many levels the dimmer will change for each dimming step. |
| 12 | ALL ON/ALL OFF Dim Rate | Sets the dim rate for the all on/off command |
| 13 | Disable Group 4 During a Dim Command | Change behavior of command to Group 4 during Dim Command |
| 14 | Enable Shade Control Group 2 | Enable Shade Control Group 2 |
| 15 | Enable Shade Control Group 3 | Enable Shade Control Group 3 |
| 19 | LED Transmission Indication | Change behavior of LED during transmission to group 1-4 |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Defines the behavior when transmitting dim commands The ZDW103 can send Dim commands to Z-Wave enabled dimmers. The Dim command has a start level embedded in it. A dimmer receiving this command will start dimming from that start level. However, the command also has a bit that indicates whether the dimmer should ignore the start level. If the bit is set to 1, the dimmer will ignore the start level and instead start dimming from its current level. To clear this bit, configure this parameter to the value of 0. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Use transmisison start level |
| 1 | Ignore transmisison start level |
The manufacturer defined default value is 1 (Ignore transmisison start level).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Disable transmission of command to Group 4
You may wish to disable transmitting commands to Z-Wave devices that are in Group 4 without “un-associating” those devices from the group. Setting parameter 2 to the value of 1 will stop the ZDW103 from transmitting to devices that are “associated” into Group 4.
It is possible that you may only want the units in Group 4 to track when the dimmer is being turned ON and OFF and not when dimming.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Enable transmission to Group 4 |
| 1 | Disable transmission to Group 4 |
The manufacturer defined default value is 0 (Enable transmission to Group 4).
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Defines the behavior of the blue LED. Default is Night Light mode where LED is on when switch is off. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | LED on when switch is ON |
| 1 | LED on when switch is OFF |
The manufacturer defined default value is 0 (LED on when switch is ON).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Change the top of the switch to OFF and the bottom of the switch to ON. Note: If you invert the switches and also install the product upside down, remember the load will now be controlled by the right, not the left switch. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No |
| 1 | Yes |
The manufacturer defined default value is 0 (No).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
This dimmer will start dimming from its current level.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No |
| 1 | Yes |
The manufacturer defined default value is 0 (No).
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Change behavior of dim level information update When you press and hold the bottom of the ZDW103 paddle once, the Z-Wave devices that are associated into Group 1 are sent the Dim command. After you release the paddle, the ZDW103 follows up by commanding the devices to go to the same level of the ZDW103. By default, the ZDW103 is set not to do this. To enable ZDW103 to do this set this parameter to 0. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Send level command |
| 1 | Don’t send level command |
The manufacturer defined default value is 1 (Don’t send level command).
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Indicates how many levels the dimmer will change for each dimming step.
Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_7_1 and is of type INTEGER.
Sets the rate at which the dimmer changes the light level. This value indicates in 10 millisecond resolution, how often the dim level will change. For example, if you set this parameter to 1, then every 10ms the dim level will change. If you set it to 255, then every 2.55 seconds Values in the range 1 to 255 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Indicates how many levels the dimmer will change for each dimming step.
Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_9_1 and is of type INTEGER.
Sets the dim rate This value indicates in 10 millisecond resolution, how often the dim level will change. For example, if you set this parameter to 1, then every 10ms the dim level will change. If you set it to 255, then every 2.55 seconds the dimmer will change. Values in the range 1 to 255 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
Indicates how many levels the dimmer will change for each dimming step.
Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_11_1 and is of type INTEGER.
Sets the dim rate for the all on/off command This value indicates in 10 millisecond resolution, how often the dim level will change. For example, if you set this parameter to 1, then every 10ms the dim level will change. If you set it to 255, then every 2.55 seconds the dimmer will change. Values in the range 1 to 255 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_12_1 and is of type INTEGER.
Change behavior of command to Group 4 during Dim Command After the ZDW103 is commanded to stop dimming, it will then command the Z-Wave devices in Group 4 to the ZDW103’s new level. To prevent the ZDW103 from commanding the Z-Wave devices in Group 4 during this particular occurrence, set Parameter 13 to the value of 1. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Enable transmission to Group 4 |
| 1 | Disable transmission to Group 4 |
The manufacturer defined default value is 0 (Enable transmission to Group 4).
This parameter has the configuration ID config_13_1 and is of type INTEGER.
Enable Shade Control Group 2 The ZDW103 can control shade control devices via its group 2 if this configuration parameter is set to 1. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
The manufacturer defined default value is 0 (Disabled).
This parameter has the configuration ID config_14_1 and is of type INTEGER.
Enable Shade Control Group 3 The ZDW103 can control shade control devices via its group 3 if this configuration parameter is set to 1. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
The manufacturer defined default value is 0 (Disabled).
This parameter has the configuration ID config_15_1 and is of type INTEGER.
Change behavior of LED during transmission to group 1-4 The ZDW103 will flicker its LED when it is transmitting to any of its 4 groups. This flickering can be set to not flicker at all (set to 0), to flicker the entire time it is transmitting (set to 1), or to flicker for only 1 second when it begins transmitting (set to 2). By default, the ZDW103 is set to flicker for only 1 second. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No flicker |
| 1 | Flicker during all transmission |
| 2 | Flicker first second of transmission |
The manufacturer defined default value is 2 (Flicker first second of transmission).
This parameter has the configuration ID config_19_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ZDW103 supports 4 association groups.
Tap once
Association group 1 supports 5 nodes.
Tap twice
Association group 2 supports 5 nodes.
Tap three time
Association group 3 supports 5 nodes.
Group to update transmitter or controler
Association group 4 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.