| layout | title |
|---|---|
documentation |
DSB29 - ZWave |
{% include base.html %}
This describes the Z-Wave device DSB29, manufactured by AEON Labs with the thing type UID of aeon_dsb29_00_000.
The device is in the category of Door, defining Door sensors.
The DSB29 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.
The DSB29 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the Wakeup Information section below for further information.
The DSB29 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour.
The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.
The following table summarises the channels available for the DSB29 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Binary Sensor | sensor_door | Door | Contact |
| Alarm (general) | alarm_general | Door | Switch |
| Battery Level | battery-level | Battery | Number |
Indicates if the door/window is open or closed.
The sensor_door channel supports the Contact item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Contact item type -:
| Value | Label |
|---|---|
| OPEN | Open |
| CLOSED | Closed |
Indicates if an alarm is triggered.
The alarm_general channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.
The battery-level channel supports the Number item and is in the Battery category.
The following table provides a summary of the 5 configuration parameters available in the DSB29. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Send Sensor binary report on open/close events | |
| 2 | Enable wake up 10 minutes when power on | |
| 3 | Send Basic Set on open/close event | |
| 121 | command class to use for open/close | parameter 4 (LSB) |
| 121 | command class to use for open/close | see overview (parameter 3) |
| Wakeup Interval | Sets the interval at which the device will accept commands from the controller | |
| Wakeup Node | Sets the node ID of the device to receive the wakeup notifications |
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | On for opened, Off for closed |
| 1 | Off for opened, On for closed |
The manufacturer defined default value is 0 (On for opened, Off for closed).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No |
| 1 | Yes |
The manufacturer defined default value is 0 (No).
This parameter has the configuration ID config_2_1 and is of type INTEGER.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | On for opened, Off for closed |
| 1 | Off for opened, On for closed |
The manufacturer defined default value is 0 (On for opened, Off for closed).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
parameter 4 (LSB) Set to 0 for no report
Set to 1 for BATTERY report
Set to 16 for SENSOR_BINARY report
Set to 17 for SENSOR_BINARY and BATTERY The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | not set |
| 1 | BATTERY report |
| 16 | SENSOR BINARY report |
| 17 | SENSOR BINARY and BATTERY report |
The manufacturer defined default value is 0 (not set).
This parameter has the configuration ID config_121_4_000000FF and is of type INTEGER.
see overview (parameter 3) set to 0 for no report
set to 1 for BASIC report (default) The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | not set |
| 1 | BASIC report |
The manufacturer defined default value is 1 (BASIC report).
This parameter has the configuration ID config_121_4_0000FF00 and is of type INTEGER.
The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.
This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.
Note that this setting does not affect the devices ability to send sensor data, or notification events.
This parameter has the configuration ID wakeup_interval and is of type INTEGER.
When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.
This parameter has the configuration ID wakeup_node and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The DSB29 supports 1 association group.
Association group 1 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_WAKE_UP_V2 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.