| layout | title |
|---|---|
documentation |
DSC18 - ZWave |
{% include base.html %}
This describes the Z-Wave device DSC18, manufactured by AEON Labs with the thing type UID of aeon_dsc18_00_000.
The DSC18 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
No device information is provided in the database. Consider updating the database to improve the documentation.
The following table summarises the channels available for the DSC18 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Switch | switch_binary | Switch | Switch |
| Electric meter (watts) | meter_watts | Energy | Number |
| Electric meter (amps) | meter_current | Energy | Number |
| Electric meter (kWh) | meter_kwh | Energy | Number |
| Electric meter (volts) | meter_voltage | Energy | Number |
| Reset Meter | meter_reset | Energy | Switch |
Switch the power on and off.
The switch_binary channel supports the Switch item and is in the Switch category.
Indicates the instantaneous power consumption.
The meter_watts channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous current consumption.
The meter_current channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous voltage.
The meter_voltage channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Reset the meter.
The meter_reset channel supports the Switch item and is in the Energy category.
The following table provides a summary of the 13 configuration parameters available in the DSC18. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 2 | Make Micro Smart Switch Blink | |
| 3 | Current Overload Protection | |
| 80 | Notification on Status Change | |
| 90 | Automated sending of a Report triggered by minimal change of value. | |
| 91 | Minimum Change to send Report (Watt) | |
| 92 | Minimum Change to send Report (%) | |
| 101 | Which reports need to send automatically in timing intervals for group 1 | |
| 102 | Which reports need to send automatically in timing intervals for group 2 | |
| 103 | Which reports need to send automatically in timing intervals for group 3 | |
| 111 | Interval to send out reports of group 1 | |
| 112 | Interval to send out reports of group 2 | |
| 113 | Interval to send out reports of group 3 | |
| 120 | Turn External Button Mode | |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_2_2 and is of type INTEGER.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Deactivate |
| 1 | Activate |
The manufacturer defined default value is 0 (Deactivate).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Deactivate |
| 1 | Hail CC Sent |
| 2 | Basic CC Report Sent |
The manufacturer defined default value is 0 (Deactivate).
This parameter has the configuration ID config_80_1 and is of type INTEGER.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Deavtivate |
| 1 | Activate |
The manufacturer defined default value is 0 (Deavtivate).
This parameter has the configuration ID config_90_1 and is of type INTEGER.
Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 25.
This parameter has the configuration ID config_91_2 and is of type INTEGER.
Values in the range 0 to 255 may be set.
The manufacturer defined default value is 5.
This parameter has the configuration ID config_92_1 and is of type INTEGER.
Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 4.
This parameter has the configuration ID config_101_4 and is of type INTEGER.
Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 8.
This parameter has the configuration ID config_102_4 and is of type INTEGER.
Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_103_4 and is of type INTEGER.
Values in the range 1 to 2678400 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_111_4 and is of type INTEGER.
Values in the range 1 to 2678400 may be set.
The manufacturer defined default value is 600.
This parameter has the configuration ID config_112_4 and is of type INTEGER.
Values in the range 1 to 2678400 may be set.
The manufacturer defined default value is 600.
This parameter has the configuration ID config_113_4 and is of type INTEGER.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Momentary Button Mode |
| 1 | 2 State Switch Mode |
| 2 | 3 Way Switch Mode |
The manufacturer defined default value is 255.
This parameter has the configuration ID config_120_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The DSC18 supports 2 association groups.
Association group 1 supports 5 nodes.
Association group 2 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_CRC_16_ENCAP_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.