| layout | title |
|---|---|
documentation |
heatapp! floor - ZWave |
{% include base.html %}
heatapp! floor heatapp! floor is a controller for thermal actuators in underfloor heating installations and is part of the heatapp! system, providing individual circ
This describes the Z-Wave device heatapp! floor, manufactured by EbV with the thing type UID of ebv_heatappfloor_00_000.
The device is in the category of Radiator Control, defining Controls on radiators used to heat up rooms.
The heatapp! floor supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Information at the z-wave alliance product cataloge: https://products.z-wavealliance.org/products/1249
Press the learn key (10) for 2 seconds that will start the inclusion process on the device.
Press the learn key (10) for 2 seconds that will start the exclusion process on the device.
The following table summarises the channels available for the heatapp! floor -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Switch | switch_binary | Switch | Switch |
| Switch 1 | switch_binary1 | Switch | Switch |
| Switch 2 | switch_binary2 | Switch | Switch |
| Switch 3 | switch_binary3 | Switch | Switch |
| Switch 4 | switch_binary4 | Switch | Switch |
| Switch 5 | switch_binary5 | Switch | Switch |
| Switch 6 | switch_binary6 | Switch | Switch |
| Switch 7 | switch_binary7 | Switch | Switch |
| Switch 8 | switch_binary8 | Switch | Switch |
Switch the power on and off.
The switch_binary channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary1 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary2 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary3 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary4 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary5 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary6 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary7 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary8 channel supports the Switch item and is in the Switch category.
The following table provides a summary of the 2 configuration parameters available in the heatapp! floor. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Missing Radio Link time | Maximum time device will wait for reconnection before going to emergency mode (All switches ON). |
| 2 | Relay type | 0 normal open, 1 normal close, 2 switching |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Maximum time device will wait for reconnection before going to emergency mode (All switches ON). It is maximum time device will wait for reconnection before it going ot emergency mode (All switches ON). It is possible to set in the range of 10min to 4hours. Default value is 30min, only 1 Byte Values in the range 10 to 240 may be set.
The manufacturer defined default value is 30.
This parameter has the configuration ID config_1_1 and is of type INTEGER.
0 normal open, 1 normal close, 2 switching Configuaration parameter2 relay type. Default relay type is normal open, only 1 Byte. 0 normal open, 1 normal close, 2 switching The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Normal open |
| 1 | Normal close |
| 2 | Switching |
The manufacturer defined default value is 0 (Normal open).
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The device does not support associations.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_VERSION_V2 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.