| layout | title |
|---|---|
documentation |
DMMS1 - ZWave |
{% include base.html %}
This describes the Z-Wave device DMMS1, manufactured by Elexa Consumer Products Inc. with the thing type UID of elexa_dmms1_00_000.
The device is in the category of Motion Detector, defining Motion sensors/detectors.
The DMMS1 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.
The DMMS1 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the Wakeup Information section below for further information.
Z-Wave Plus Motion Detector with Light Sensor
- Bring Motion Detector to within 10 feet (3 meters) of the controller
- Remove the cover of the Motion Detector by twisting it apart
- Put the controller into inclusion mode
- Press the Connect Button quickly 3 times in a row
The LED Indicator will flash five times indicating inclusion.
- Remove the cover of the Motion Detector by twisting apart and make sure the Motion Detector is powered
- Put the controller into exclusion mode
- Press the Connect Button quickly three times in a row
The LED Indicator will flash five times indicating exclusion/disconnection
Factory Reset:
- Remove the cover of the Motion Detector by twisting apart and make sure the Motion Detector is powered
- Hold the Connect Button for 10 seconds until the LED Indicator blinks once, then release the button.
The DMMS1 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour.
The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.
- Remove the cover of the Motion Detector by twisting apart and make sure the Motion Detector is powered
- Press the Connect Button quickly three times in a row
The following table summarises the channels available for the DMMS1 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Binary Sensor | sensor_binary | Door | Switch |
| Sensor (luminance) | sensor_luminance | Number | |
| Tamper Alarm | alarm_tamper | Switch | |
| Motion Alarm | alarm_motion | Door | Switch |
| Battery Level | battery-level | Battery | Number |
Indicates if a sensor has triggered.
The sensor_binary channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| ON | Triggered |
| OFF | Untriggered |
Indicates the current light reading.
The sensor_luminance channel supports the Number item. This is a read only channel so will only be updated following state changes from the device.
Indicates if the tamper alarm is triggered.
The alarm_tamper channel supports the Switch item. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Indicates if a motion alarm is triggered.
The alarm_motion channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.
The battery-level channel supports the Number item and is in the Battery category.
The following table provides a summary of the 10 configuration parameters available in the DMMS1. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Motion Sensitivity | 8 = high; 255 = low |
| 2 | Trigger ON Duration | delay after motion before turning OFF |
| 3 | Trigger Action | Brightness to turn on the associated device 1-99, 255=ON |
| 4 | Motion Detection | 255=Motion Detection Enabled |
| 5 | Light Trigger Level | Max Light level which enables motion trigger |
| 6 | Motion Trigger Interval | Minimum time between motion triggers. |
| 7 | Light Polling Interval | Interval between light level reporting |
| 8 | Light Trigger | 255=enable Light sensor |
| 9 | Light Report | Light level change to be reported. |
| 10 | LED Notifications | 0=disable, 1=enable |
| Wakeup Interval | Sets the interval at which the device will accept commands from the controller | |
| Wakeup Node | Sets the node ID of the device to receive the wakeup notifications |
8 = high; 255 = low Adjust detection by choosing a value from 8 to 255, where 8 stands for high sensitivity level (detection of the smallest movement) and 255 stands for very low sensitivity level Values in the range 8 to 255 may be set.
The manufacturer defined default value is 12.
This parameter has the configuration ID config_1_1 and is of type INTEGER.
delay after motion before turning OFF Set the duration (in seconds) you want the associated device to stay ON for after being triggered by the sensor before it automatically turns OFF. Must be greater than value set in parameter 6. Values in the range 5 to 600 may be set.
The manufacturer defined default value is 30.
This parameter has the configuration ID config_2_2 and is of type INTEGER.
Brightness to turn on the associated device 1-99, 255=ON You can choose if your Mini Sensor turns an associated device on or off when sending the BASIC SET command. Use value 0 to turn the associated device OFF and value 255 to turn it ON. Adjust brightness level for a Z-Wave dimmer (Multilevel switch) by putting in any value between 1 and 99. Values in the range 0 to 255 may be set.
The manufacturer defined default value is 255.
This parameter has the configuration ID config_3_1 and is of type INTEGER.
255=Motion Detection Enabled
Values in the range 0 to 255 may be set.
The manufacturer defined default value is 255.
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Max Light level which enables motion trigger Set your light sensor as a secondary trigger for associated devices. If light level in a room falls beyond the set point and motion is detected, the Mini Sensor will send BASIC_SET command to associated devices to turn ON. The number entered as the value corresponds to the number of LUX. By default, if motion has been detected by your Mini Sensor, the associated device will turn ON if light level last reported by the sensor is under 100 LUX. Values in the range 0 to 1000 may be set.
The manufacturer defined default value is 100.
This parameter has the configuration ID config_5_2 and is of type INTEGER.
Minimum time between motion triggers. Adjust the time (in seconds) when motion is reported again after initial trigger. By default, with continued motion, the Mini Sensor will report motion again 8 seconds after it's last detection. The value set for this parameter can NOT be greater than value set in parameter 2. NOTE: Small interval will increase activity and decrease battery life. Values in the range 1 to 8 may be set.
The manufacturer defined default value is 8.
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Interval between light level reporting Decide how often (in seconds) you want the Mini Sensor to report light level to the controller and associated devices. By default, the Mini Sensor will report light level values every 3 minutes. The value set for this parameter can NOT be greater than the wake-up interval. NOTE: Small interval will increase activity and decrease battery life. Values in the range 60 to 36000 may be set.
The manufacturer defined default value is 180.
This parameter has the configuration ID config_7_2 and is of type INTEGER.
255=enable Light sensor Use this parameter to enable and disable the light sensor as secondary trigger. If this feature is enabled, the Mini Sensor will activate associated devices based on motion AND light level set in parameter 5 Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Light level change to be reported. Choose light level (in LUX) change to be reported by the Mini Sensor to the controller. By default, the sensor will report any change of 100 LUX or more. Values in the range 0 to 255 may be set.
The manufacturer defined default value is 255.
This parameter has the configuration ID config_9_1 and is of type INTEGER.
0=disable, 1=enable Use this parameter to turn LED notifications on or off for motion detection. Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.
This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.
Note that this setting does not affect the devices ability to send sensor data, or notification events.
This parameter has the configuration ID wakeup_interval and is of type INTEGER.
When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.
This parameter has the configuration ID wakeup_node and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The DMMS1 supports 4 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Lifeline communication of motion / no motion and light level status to Z-Wave controller. Supported command classes: NOTIFICATION_REPORT_V4 SENSOR_BINARY_REPORT_V2 SENSOR_MULTILEVEL_REPORT_V7 BATTERY_REPORT DEVICE_RESET_LOCALLY_NOTIFICATION
Association group 1 supports 5 nodes.
BASIC_SET Trigger associated devices control command communication to associated Z-Wave devices in the network. Use parameters 2, 3, 5, and 8 to configure this group’s settings. Supported command classes: BASIC_SET
Association group 2 supports 5 nodes.
NOTIFICATION_REPORT_V4 notifications to Z-Wave devices associated in this group. Supported command classes: NOTIFICATION_REPORT_V4
Association group 3 supports 5 nodes.
SENSOR_BINARY_REPORT_V2 notifications to Z-Wave devices associated in this group. Supported command classes: SENSOR_BINARY_REPORT_V2
Association group 4 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_BINARY_V2 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V8 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_WAKE_UP_V2 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.