| layout | title |
|---|---|
documentation |
Spirit - ZWave |
{% include base.html %}
This describes the Z-Wave device Spirit, manufactured by Eurotronics with the thing type UID of eurotronic_spirit_00_000.
The device is in the category of Radiator Control, defining Controls on radiators used to heat up rooms.
The Spirit supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.
Spirit Z-Wave Plus is a Z-Wave radio standard compatible energy-saving radiator thermostat.
FLiRS (Frequently Listening Receiver Slave): Spirit Z-Wave uses FLiRS to provide short latency and short responding times.
Start Inclusion mode of your primary Z-Wave Controller. Press the Boost-Button. Spirit Z-Wave Plus will show the assigned NodeID.
Start Exclusion mode of your primary Z-Wave Controller. Now press and hold the boost button of the Spirit Z-Wave Plus for at least 5 seconds.
The following table summarises the channels available for the Spirit -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Dimmer | switch_dimmer | DimmableLight | Dimmer |
| Current temperature | sensor_temperature | Temperature | Number:Temperature |
| External temperature | sensor_report | Number | |
| Thermostat mode | thermostat_mode | Temperature | Number |
| Setpoint (heat) | thermostat_setpoint | Temperature | Number:Temperature |
| Setpoint (energy heat) | thermostat_setpoint | Temperature | Number:Temperature |
| Alarm (system) | alarm_system | Switch | |
| Alarm (power) | alarm_power | Door | Switch |
| Battery Level | battery-level | Battery | Number |
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.
Indicates the current temperature.
The sensor_temperature channel supports the Number:Temperature item and is in the Temperature category.
Send report to device.
The sensor_report channel supports the Number item.
Sets the thermostat.
The thermostat_mode channel supports the Number item and is in the Temperature category.
The following state translation is provided for this channel to the Number item type -:
| Value | Label |
|---|---|
| 0 | Off |
| 1 | Heat |
| 2 | Cool |
| 3 | Auto |
| 4 | Aux Heat |
| 5 | Resume |
| 6 | Fan Only |
| 7 | Furnace |
| 8 | Dry Air |
| 9 | Moist Air |
| 10 | Auto Changeover |
| 11 | Heat Economy |
| 12 | Cool Economy |
| 13 | Away |
Precision 0,1 and 2 Scale Celsius and Fahrenheit Temp. Range 8°C-28°C
Sets the thermostat setpoint.
The thermostat_setpoint channel supports the Number:Temperature item and is in the Temperature category.
Precision 0,1 and 2 Scale Celsius and Fahrenheit Temp. Range 8°C-28°C
Sets the thermostat setpoint.
The thermostat_setpoint channel supports the Number:Temperature item and is in the Temperature category.
Indicates if a system alarm is triggered.
The alarm_system channel supports the Switch item. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Indicates if a power alarm is triggered.
The alarm_power channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.
The battery-level channel supports the Number item and is in the Battery category.
The following table provides a summary of the 8 configuration parameters available in the Spirit. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | LCD Invert | LCD Invert |
| 2 | LCD Timeout | LCD Timeout |
| 3 | Backlight | Backlight |
| 4 | Battery report | Battery report |
| 5 | Measured Temperature report | Measured Temperature report |
| 6 | Valve opening percentage report | Valve opening percentage report |
| 7 | Window open detection | Window open detection |
| 8 | Temperature Offset | Measured Temperature offset |
LCD Invert
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | LCD-content normal |
| 1 | LCD-content inverted (UK Edition) |
The manufacturer defined default value is 0 (LCD-content normal ).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
LCD Timeout 0: No Timeout LCD always on
5-30: LCD will turn off after 5 to 30 seconds The following option values may be configured, in addition to values in the range 5 to 30 -:
| Value | Description |
|---|---|
| 0 | No Timeout LCD always on |
The manufacturer defined default value is 0 (No Timeout LCD always on).
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Backlight
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Backlight disabled |
| 1 | Backlight enabled |
The manufacturer defined default value is 1 (Backlight enabled).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Battery report
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | system notification |
| 1 | Send battery status unsolicited once a day. |
The manufacturer defined default value is 1 (Send battery status unsolicited once a day. ).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Measured Temperature report 0: Unsolicited Temperature reporting disabled
1-50: report if temperature changed by delta = 0,1°C ... 5,0 °C
default 5: report on delta T = 0,5°C Values in the range 0 to 50 may be set.
The manufacturer defined default value is 5.
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Valve opening percentage report 0: Unsolicited valve opening percentage reporting disabled.
1-100: report if valve opening changed by delta = 1% ... 100% Values in the range 0 to 100 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Window open detection
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disabled |
| 1 | Sensitivity low |
| 2 | Sensitivity medium |
| 3 | Sensitivity high |
The manufacturer defined default value is 2 (Sensitivity medium).
This parameter has the configuration ID config_7_1 and is of type INTEGER.
Measured Temperature offset -50 - +50: Offsets the measured temp by-5,0°C – (+)5,0°C
128: External temp sensor will be used for regul. The following option values may be configured, in addition to values in the range -50 to 50 -:
| Value | Description |
|---|---|
| 128 | Ext temp sensor be used for regul |
The manufacturer defined default value is 0.
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The Spirit supports 1 association group.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Spirit Z-Wave Plus can only be associated with the Z-Wave controller. Commands:
BATTERY_REPORT, DEVICE_RESET_LOCALLY_NOTIFICATION, THERMOSTAT_MODE_REPORT, THERMOSTAT_SETPOINT_REPORT, NOTIFICATION_REPORT, PROTECTION_REPORT, SENSOR_MULTILEVEL_REPORT, SWITCH_MULTILEVEL_REPORT
Association group 1 supports 1 node.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5 | |
| COMMAND_CLASS_THERMOSTAT_MODE_V3 | |
| COMMAND_CLASS_THERMOSTAT_SETPOINT_V3 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V8 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_PROTECTION_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V3 | |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_SECURITY_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.