Skip to content

Latest commit

 

History

History
162 lines (102 loc) · 5.87 KB

lpm15_0_0.md

File metadata and controls

162 lines (102 loc) · 5.87 KB
layout title
documentation
LPM-15 - ZWave

{% include base.html %}

LPM-15 Appliance module

This describes the Z-Wave device LPM-15, manufactured by Evolve with the thing type UID of evolve_lpm15_00_000.

The device is in the category of Power Outlet, defining Small devices to be plugged into a power socket in a wall which stick there.

LPM-15 product image

The LPM-15 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.

Overview

The Evolve Plug-in Appliance Module is a component of the Evolve lighting control system and is fully scene capable. The Appliance Module is plugged into any standard grounded AC wall outlet, and the appliance or other device is then plugged into the module. Once connected, the appliance/device can be easily turned ON or OFF remotely via the Z-Wave network.

This device is compatible with Z-Wave security systems and can handle a maximum of the following loads:

  • Incandescent – 600W, 120 VAC
  • Resistive – 15 amps (1800 watts), 120 VAC
  • Motor – ½ H.P., 120 VAC

This Plug-in Appliance Module is designed to work with other Evolve enabled devices. Evolve nodes of other types can be included in the network and will also act as repeaters to increase the range of the network.

As part of a Z-Wave network, the LPM-15 will also act as a wireless repeater to ensure that commands intended for another device in the network are received. This is useful when the device would otherwise be out of the radio range of the wireless controller.

Inclusion Information

  1. Start a search for new z-wave binding items via the add things interface
  2. Press the button on the front of the unit to include

Note: will work with inclusion set to network-wide.

Factory reset procedure:

  1. Unplug device and wait 15 seconds
  2. Plug device in and immediately press the front button twice (the two presses must occur within 20 seconds of plugging in the unit.

Exclusion Information

  1. Place controller in exclude mode
  2. Press button on front of device

Channels

The following table summarises the channels available for the LPM-15 -:

Channel Channel Id Category Item Type
Switch switch_binary Switch Switch
Scene Number scene_number Number

Switch

Switch the power on and off.

The switch_binary channel supports the Switch item and is in the Switch category.

Scene Number

Triggers when a scene button is pressed.

The scene_number channel supports the Number item.

Device Configuration

The following table provides a summary of the 2 configuration parameters available in the LPM-15. Detailed information on each parameter can be found in the sections below.

Param Name Description
3 Night Light Defines the behavior of the blue LED; default has LED on when switch is off.
4 Invert Switch Change the top of the switch to OFF and the bottom of the switch to ON.
Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands

Parameter 3: Night Light

Defines the behavior of the blue LED; default has LED on when switch is off.

The following option values may be configured -:

Value Description
0 LED on when switch is OFF
1 LED on when switch is ON
2 LED always off

The manufacturer defined default value is 0 (LED on when switch is OFF).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Invert Switch

Change the top of the switch to OFF and the bottom of the switch to ON. Note: If you invert the switches and also install the product upside down, remember the load will now be controlled by the right, not the left switch. The following option values may be configured -:

Value Description
0 No
1 Yes

The manufacturer defined default value is 0 (No).

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -:

Value Description
0 Exclude from All On and All Off groups
1 Include in All On group
2 Include in All Off group
255 Include in All On and All Off groups

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The device does not support associations.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1 Linked to BASIC
COMMAND_CLASS_SWITCH_ALL_V1
COMMAND_CLASS_SCENE_ACTIVATION_V1
COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1
COMMAND_CLASS_CONFIGURATION_V1
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1
COMMAND_CLASS_POWERLEVEL_V1
COMMAND_CLASS_PROTECTION_V1
COMMAND_CLASS_VERSION_V1

Documentation Links

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.