| layout | title |
|---|---|
documentation |
GE 14289 (ZW3009) - ZWave |
{% include base.html %}
This describes the Z-Wave device GE 14289 (ZW3009), manufactured by Jasco Products with the thing type UID of ge_14289_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The GE 14289 (ZW3009) supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Put smart lighting control at your fingertips with the GE Z-Wave Plus Touch Sensing Dimmer. Control your lights with simple one touch dimming at the wall, by a mobile device from virtually anywhere, or by voice with Amazon Alexa or Google Assistant. The GE Z-Wave Plus Touch Dimmer offers extremely smooth and precise dimming control to detect different gestures such touch, hold, and swipe. Tap anywhere on the capacitive touch sensor to turn lights on or off and slide your finger up or down to seamlessly and smoothly adjust the brightness level of dimmable lights. The GE Touch Dimmer remembers your last brightness setting and automatically returns your lights to that level when turned on again. On, off and brightness levels can also be controlled and scheduled from anywhere! Along with conveniently saving you time and energy costs, the GE Z-Wave dimmer switch can replace any existing light switch in your home, and can be used in 2-, 3- and 4-way applications. You may also coordinate the Z-Wave dimmer with your home’s decor using the included white and light almond touch pad. Experience the comfort of smart home automation with the GE Z-Wave Plus In-Wall Touch Sensing Smart Dimmer.
- Follow the instructions for your Z-Wave controller to add a device tothe Z-Wave network.
- Once the controller is ready to add your device, press and release anywhere on the touch panel.
- Follow the instructions for your Z-Wave controller to remove a device from the Z-Wave network.
- Once the controller is ready to remove your device, press and hold the side button (G) of the smart dimmer. While holding, press and release anywhere on the touchpanel, then release the side button to remove it from the network.
The following table summarises the channels available for the GE 14289 (ZW3009) -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Dimmer | switch_dimmer | DimmableLight | Dimmer |
| Scene Number | scene_number | Number |
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.
Triggers when a scene button is pressed.
The scene_number channel supports the Number item.
The device has no configuration parameters defined.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The device does not support associations.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V2 | |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_CRC_16_ENCAP_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.