| layout | title |
|---|---|
documentation |
In-Wall Smart Motion Dimmer - ZWave |
{% include base.html %}
This describes the Z-Wave device In-Wall Smart Motion Dimmer, manufactured by Jasco Products with the thing type UID of ge_26933_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The In-Wall Smart Motion Dimmer supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Set your life in motion with the Z-Wave Plus In-Wall Smart Motion Switch. This energy-efficient sensor works with your home’s gateway to wirelessly trigger scenes and send alerts to your smartphone or tablet whenever motion is has turned lights on or off.
Three different modes offer the best lighting option for you: occupancy, vacancy and manual. In occupancy mode, the lights will automatically turn on when you enter the room and automatically turn off once you’ve left (customizable between 5 seconds and 30 minutes).
In vacancy mode, the lights are turned on manually and will turn off automatically after a preset amount of time. In manual mode, the lights will function as a normal light switch and manually turn on and off. Along with conveniently saving you time and energy costs, the smart motion dimmer can replace any existing light switch in your home, and can be used in 3- and 4-way applications.
You may also coordinate the switch with your household decor with the included white and light almond buttons. Experience the comfort of automation in your life when you come home to the Z-Wave Plus In Wall Smart Motion Switch.
- Wirelessly trigger scenes and send alerts when motion detection has turned lights on or off
- Remotely monitor with any mobile device (Requires Z-Wave gateway or controller)
- Compatible with all certified Z-Wave devices
- Requires in-wall installation with hard-wired connections - neutral wire required
- Can be used in 3- and 4-way applications
- Works with all dimmable LED, CFL, halogen and incandescent bulbs
- Multiple operation modes: Occupancy - auto ON/auto OFF, Vacancy - manual ON/auto OFF, Manual - manual ON/OFF
- Built-in timer lets you set length of time light stays on after motion ceases - from 5 seconds to 30 minutes
- 3 sensitivity levels - low, medium, high
- Includes white and light almond paddles
- Indoor use only
- Specification Value Max Load 600W Incandescent
- 150W Dimmable Power 120VAC, 60Hz
- Operating Temp. Rge 32-104°F (0-40°C)
- Signal Frequency 908.4/916MHz
- Wireless Range Up to 150 feet
Adding your device to a Z-Wave network
- Follow the instructions for your Z-Wave certified controller to add the smart dimmer to the Z-Wave network.
- Once the controller is ready to add your smart dimmer, press and release the top or bottom button on the smart dimmer to include it in the network.
To return to factory defaults
Press and release the top button ten times within 5 seconds. The LED will flash 3 times quickly confirming change.
To remove and reset the device
- Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
- Once the controller is ready to remove your device, press and release the top button on the smart dimmer to remove it from the network.
To return to factory defaults
Press and release the top button ten times within 5 seconds. The LED will flash 3 times quickly confirming change.
The following table summarises the channels available for the In-Wall Smart Motion Dimmer -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
| Scene Number | scene_number | scene_number | Number | |
| Operation Mode | config_decimal | config_decimal | Number | |
| Alarm (burglar) | alarm_burglar | alarm_burglar | Door | Switch |
| Switch 1 | switch_dimmer1 | switch_dimmer | DimmableLight | Dimmer |
| Motion Alarm | alarm_motion2 | alarm_motion | Motion | Switch |
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel and is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Triggers when a scene button is pressed.
The scene_number channel and is of type scene_number and supports the Number item.
Sets how the light responds to motion
1=Manual, 2=Vacancy, 3=Occupancy
Generic class for configuration parameter.
The config_decimal channel and is of type config_decimal and supports the Number item.
Indicates if the burglar alarm is triggered.
The alarm_burglar channel and is of type alarm_burglar and supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer1 channel and is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Indicates if a motion alarm is triggered.
The alarm_motion2 channel and is of type alarm_motion and supports the Switch item and is in the Motion category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
The following table provides a summary of the 19 configuration parameters available in the In-Wall Smart Motion Dimmer. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Timeout Duration | Amount of time the light stays on after motion stops |
| 2 | Dim Level | Brightness of associated light(s) |
| 3 | Operation Mode | Sets how the light responds to motion |
| 4 | Association Mode | Enable/Disable Association Mode |
| 5 | Invert Switch | In a 3-way configuration, invert the connected Add-On Switch buttons |
| 6 | Motion Sensor | Enable/Disable Motion Sensor |
| 7 | Remote Control Dim Step | Sets the step size of the dimmer. |
| 8 | Remote Control Dim Rate | Set the speed at which the dim level will change. (10 millisecond precision) |
| 9 | Local Control Dim Step | Sets the step size of the dimmer. |
| 10 | Local Control Dim Rate | Set the speed at which the dim level will change. (10 millisecond precision) |
| 11 | ALL ON/ALL OFF Dim Step | Sets the step size of the dimmer. |
| 12 | ALL ON/ALL OFF Dim Rate | Set the speed at which the dim level will change. (10 millisecond precision) |
| 13 | Motion Sensor Sensitivity | Sets the amount of motion required to trigger the motion sensor. |
| 14 | Light Sensing | Enable/Disable whether motion sensor only turns light on if room is dark |
| 15 | Reset Cycle | Reset Cycle |
| 16 | Switch Mode | Enable / Disable plain switch functionality |
| 17 | Switch Level | Set power level for plain switch functionality |
| 18 | Dim Up Rate | |
| 19 | Exclusion mode | |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Amount of time the light stays on after motion stops
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Test (5s) |
| 1 | 1 minute |
| 5 | 5 minutes |
| 15 | 15 minutes |
| 30 | 30 minutes |
| 255 | Disable timeout |
The manufacturer defined default value is 5 (5 minutes).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Brightness of associated light(s) Valid values are 0-99 or 255 for last dimming level Values in the range 0 to 255 may be set.
The manufacturer defined default value is 255.
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Sets how the light responds to motion Occupancy – Light turns on automatically with motion and off automatically without motion
Vacancy – Light turns on manually and off automatically without motion
Manual – Light only turns on and off manually The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | Manual |
| 2 | Vacancy |
| 3 | Occupancy |
The manufacturer defined default value is 3 (Occupancy).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Enable/Disable Association Mode
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
The manufacturer defined default value is 1 (Enabled).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
In a 3-way configuration, invert the connected Add-On Switch buttons
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
The manufacturer defined default value is 0 (Disabled).
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Enable/Disable Motion Sensor
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
The manufacturer defined default value is 1 (Enabled).
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Sets the step size of the dimmer.
1=Default
2-99=Steps/Levels
Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_7_1 and is of type INTEGER.
Set the speed at which the dim level will change. (10 millisecond precision) When set to 1, the dim level will change every 10ms, when set to 255 the dim level will change every 2.55 seconds. The default value is 3 / 30 ms. Values in the range 1 to 255 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_8_2 and is of type INTEGER.
Sets the step size of the dimmer.
1=Default
2-99=Steps/Levels
Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_9_1 and is of type INTEGER.
Set the speed at which the dim level will change. (10 millisecond precision) When set to 1, the dim level will change every 10ms, when set to 255 the dim level will change every 2.55 seconds. The default value is 3 / 30 ms. Values in the range 1 to 255 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_10_2 and is of type INTEGER.
Sets the step size of the dimmer.
1=Default
2=99=Steps/Levels
Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_11_1 and is of type INTEGER.
Set the speed at which the dim level will change. (10 millisecond precision) When set to 1, the dim level will change every 10ms, when set to 255 the dim level will change every 2.55 seconds. The default value is 3 / 30 ms. Values in the range 1 to 255 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_12_2 and is of type INTEGER.
Sets the amount of motion required to trigger the motion sensor.
The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | High |
| 2 | Medium |
| 3 | Low |
The manufacturer defined default value is 2 (Medium).
This parameter has the configuration ID config_13_1 and is of type INTEGER.
Enable/Disable whether motion sensor only turns light on if room is dark Light Sensing does not apply in Manual or Vacancy modes The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
The manufacturer defined default value is 0 (Disabled).
This parameter has the configuration ID config_14_1 and is of type INTEGER.
Reset Cycle
0=disable
1=10 seconds
2=20 seconds
3=30 seconds
4=45 seconds
5 to 109 = 15 second intervals, starting at 60 seconds
110=27 minutes 15 seconds
Values in the range 0 to 110 may be set.
The manufacturer defined default value is 2.
This parameter has the configuration ID config_15_2 and is of type INTEGER.
Enable / Disable plain switch functionality
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
The manufacturer defined default value is 0 (Disabled).
This parameter has the configuration ID config_16_1 and is of type INTEGER.
Set power level for plain switch functionality
0=disabled (default)
1-99=Brightness Level
Values in the range 0 to 99 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_17_1 and is of type INTEGER.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Dim up the light to the default level quickly (Default) |
| 1 | Dim up the light to the default level slowly |
The manufacturer defined default value is 0 (Dim up the light to the default level quickly (Default)).
This parameter has the configuration ID config_18_1 and is of type INTEGER.
This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Press and release any button on the switch (Default) |
| 1 | Press and release “X” btn and repeat for “ON“ btn |
The manufacturer defined default value is 0 (Press and release any button on the switch (Default)).
This parameter has the configuration ID config_19_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The In-Wall Smart Motion Dimmer supports 3 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Z-Wave Plus Lifeline, Multi-Level Report
Association group 1 supports 5 nodes.
Supports Basic Set and is controlled by pressing On/Off button
Association group 2 supports 5 nodes.
Supports Basic Set and is controlled by pressing On/Off button
Association group 3 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V2 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_CRC_16_ENCAP_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V4 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V2 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ALARM_V4 | Linked to BASIC |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.