| layout | title |
|---|---|
documentation |
GE 14295 - ZWave |
{% include base.html %}
This describes the Z-Wave device GE 14295, manufactured by Jasco Products with the thing type UID of ge_ge14295_00_000.
The GE 14295 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
-
Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.
-
Once the controller is ready to include your device, press and release the top or bottom of the wireless smart dimmer(rocker) to include it in the network.
-
Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network.
-
Once the controller is ready to Exclude your device, press and release the top or bottom of the wireless smart dimmer (rocker) to exclude it from the network.
The following table summarises the channels available for the GE 14295 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Dimmer | switch_dimmer | DimmableLight | Dimmer |
| Scene Number | scene_number | Number |
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.
Triggers when a scene button is pressed.
The scene_number channel supports the Number item.
The following table provides a summary of the 7 configuration parameters available in the GE 14295. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 4 | Invert Switch | Invert the ON/OFF Switch State. |
| 7 | Dim Rate Adjustments | Number of steps or levels |
| 8 | Dim Rate Adjustments | Timing of steps or levels |
| 9 | Dim Rate Adjustments | Number of steps or levels |
| 10 | Dim Rate Adjustments | Timing of steps |
| 11 | Dim Rate Adjustments | Number of steps or levels |
| 12 | Dim Rate Adjustments | Timing of steps or levels |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Invert the ON/OFF Switch State.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | (Default) No |
| 1 | Yes |
The manufacturer defined default value is 0 ((Default) No).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Number of steps or levels
Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_7_1 and is of type INTEGER.
Timing of steps or levels
Values in the range 1 to 255 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_8_2 and is of type INTEGER.
Number of steps or levels
Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_9_1 and is of type INTEGER.
Timing of steps
Values in the range 1 to 255 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_10_2 and is of type INTEGER.
Number of steps or levels
Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_11_1 and is of type INTEGER.
Timing of steps or levels
Values in the range 1 to 255 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_12_2 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The GE 14295 supports 3 association groups.
Z-Wave Plus Lifeline, Multilevel Switch Report
Association group 1 supports 5 nodes.
Supports Basic Set and is controlled with the local load
Association group 2 supports 5 nodes.
Supports Basic Set and is controlled by double pressing the On or Off button
Association group 3 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V2 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_CRC_16_ENCAP_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.