| layout | title |
|---|---|
documentation |
39354 - ZWave |
{% include base.html %}
This describes the Z-Wave device 39354, manufactured by Honeywell with the thing type UID of honeywell_39354_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The 39354 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Honeywell Z-Wave Plus On/Off Smart Light Switch, In-Wall Toggle |Built-In Repeater Range Extender | Requires Neutral Wire | ZWave Hub Required - SmartThings, Wink, Alexa Compatible, 39354
- Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.
- Once the controller is ready to include your device, press up and release on the toggle to include it in the network.
- Once your controller has confirmed that the device has been included, refresh the Z-Wave network to optimize performance.
- Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network.
- Once the controller is ready to exclude your device, press up and release on the toggle to exclude it from the network.
The following table summarises the channels available for the 39354 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Switch | switch_binary | Switch | Switch |
| Scene Number | scene_number | Number |
Switch the power on and off.
The switch_binary channel supports the Switch item and is in the Switch category.
Triggers when a scene button is pressed.
The scene_number channel supports the Number item.
The following table provides a summary of the 1 configuration parameters available in the 39354. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 4 | Invert Switch | On/Off rocker settings can be reversed |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
On/Off rocker settings can be reversed
If the switch is accidentally installed upside down with On at the bottom and Off at the top, the default On/Off rocker settings can be reversed by changing parameter 4s value to 1.
Values in the range 0 to 1 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The 39354 supports 3 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Association group 1 supports 5 nodes.
Supports Basic Set and is controlled with the local load
Association group 2 supports 5 nodes.
Controlled by double pressing the On or Off button Supports Basic Set and is controlled by double pressing the On or Off button
Association group 3 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_CRC_16_ENCAP_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.