| layout | title |
|---|---|
documentation |
ZIP-PAB01 - ZWave |
{% include base.html %}
This describes the Z-Wave device ZIP-PAB01, manufactured by Philio Technology Corp with the thing type UID of philio_pab01_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The ZIP-PAB01 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the Wakeup Information section below for further information.
The ZIP-PAB01 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour.
The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.
The following table summarises the channels available for the ZIP-PAB01 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Intensty meter 0 (amps) | meter_current | Energy | Number |
| Power factor 0 | meter_powerfactor | Energy | Number |
| Power meter 0 (watts) | meter_watts | Energy | Number |
| Electric meter (kWh) | meter_kwh | Energy | Number |
| Line voltage (volts) | meter_voltage | Energy | Number |
| Intensity meter 1 (amps) | meter_current1 | Energy | Number |
| Power factor meter 1 | meter_powerfactor1 | Energy | Number |
| Power meter 1 (watts) | meter_watts1 | Energy | Number |
| Energy meter 1 (kWh) | meter_kwh1 | Energy | Number |
| Line voltage (volts) | meter_voltage1 | Energy | Number |
| Intensity meter 2 (amps) | meter_current2 | Energy | Number |
| power factor 2 | meter_powerfactor2 | Energy | Number |
| Power meter 2 (watts) | meter_watts2 | Energy | Number |
| Energy meter 2 (kWh) | meter_kwh2 | Energy | Number |
| Line voltage 2 (volts) | meter_voltage2 | Energy | Number |
| Intensity meter 3 (amps) | meter_current3 | Energy | Number |
| Power factor 3 | meter_powerfactor3 | Energy | Number |
| Power meter 3 (watts) | meter_watts3 | Energy | Number |
| Energy meter 3 (kWh) | meter_kwh3 | Energy | Number |
| Voltage 3 (volts) | meter_voltage3 | Energy | Number |
Indicates the instantaneous current consumption.
The meter_current channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous power factor.
The meter_powerfactor channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous power consumption.
The meter_watts channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous voltage.
The meter_voltage channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous current consumption.
The meter_current1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous power factor.
The meter_powerfactor1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous power consumption.
The meter_watts1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous voltage.
The meter_voltage1 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous current consumption.
The meter_current2 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous power factor.
The meter_powerfactor2 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous power consumption.
The meter_watts2 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh2 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous voltage.
The meter_voltage2 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous current consumption.
The meter_current3 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous power factor.
The meter_powerfactor3 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous power consumption.
The meter_watts3 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh3 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous voltage.
The meter_voltage3 channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
The following table provides a summary of the 3 configuration parameters available in the ZIP-PAB01. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Power meter report period | Power meter report period, in 5 seconds unit. 720 -> 1 hour |
| 2 | Energy meter report period | The accumulated power consumption report period |
| 3 | Selected default endpoint | 1 => CT1 and CT2, 2 => CT1, 3 => CT2 |
Power meter report period, in 5 seconds unit. 720 -> 1 hour If the setting is configured for 1 hour (set value 720), the module will report its instant power consumption every 1 hour to the node of the corresponding group. The maximum interval to report its instant power consumption is 45h (5s * 32767 / 3600 = 45h) Values in the range 1 to 32767 may be set.
The manufacturer defined default value is 720.
This parameter has the configuration ID config_1_2 and is of type INTEGER.
The accumulated power consumption report period If the setting is configured for 1 hour (set value 720), the module will report its accumulated power consumption every 1 hour to the node of the corresponding group. The maximum interval to report its accumulated power consumption is 45h (5s * 32767 / 3600 = 45h) Values in the range 1 to 32767 may be set.
The manufacturer defined default value is 720.
This parameter has the configuration ID config_2_2 and is of type INTEGER.
1 => CT1 and CT2, 2 => CT1, 3 => CT2 If Controller does not use Multi Channel command class to access the endpoint of the module, you may configure the endpoint that will react to the Basic Command Class, Binary Switch command class or Meter command class V3. Values in the range 1 to 3 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ZIP-PAB01 supports 3 association groups.
Sum of CT1 and CT2 Sum of :
- Instant power consumption from CT1 and CT2 (W)
- Accumulated power consumption from CT1 and CT2 (kWh)
Association group 1 supports 1 node.
Data from CT1
- Instant power consumption from CT1 (W)
- Accumulated power consumption from CT1 (kWh)
Association group 2 supports 1 node.
Data from CT2
- Instant power consumption from CT2 (W)
- Accumulated power consumption from CT2 (kWh)
Association group 3 supports 1 node.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_CRC_16_ENCAP_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_MULTI_CHANNEL_V2 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_METER_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_METER_V3 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.