| layout | title |
|---|---|
documentation |
ZMNHCD - ZWave |
{% include base.html %}
This describes the Z-Wave device ZMNHCD, manufactured by Goap with the thing type UID of qubino_zmnhcd_00_000.
This version of the device is limited to firmware versions below 4.0
The ZMNHCD supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
ZMNHCD version S1 for version up to 4.0
To enable endpoint 2 (lamella tilt for venetian blinds), follow the procedure:
- set Param 71 to 0 -> save ( make sure it has been set really )
- set Param 71 to 1 -> save ( make sure it has been set really )
- exclude device from network and delete Node xml, stop openHAB
- switch off the power supply of the device ( according to the support team this is an alternative to wait 30s )
- switch on the power supply again and start openHAB
- include device to the network
- add the Thing to openhab via HABmin
- Be patient until the binding until processed all your nodes again
The following table summarises the channels available for the ZMNHCD -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Switch | switch_binary | Switch | Switch |
| Blinds Control | blinds_control | Blinds | Rollershutter |
| Sensor (temperature) | sensor_temperature | Temperature | Number:Temperature |
| Electric meter (watts) | meter_watts | Energy | Number |
| Electric meter (kWh) | meter_kwh | Energy | Number |
| Switch 1 | switch_binary1 | Switch | Switch |
| Blinds Control 1 | blinds_control1 | Blinds | Rollershutter |
| Switch 2 | switch_binary2 | Switch | Switch |
| Blinds Control 2 | blinds_control2 | Blinds | Rollershutter |
Switch the power on and off.
The switch_binary channel supports the Switch item and is in the Switch category.
Provides start / stop control of blinds.
The blinds_control channel supports the Rollershutter item and is in the Blinds category.
Indicates the current temperature.
The sensor_temperature channel supports the Number:Temperature item and is in the Temperature category.
Indicates the instantaneous power consumption.
The meter_watts channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh channel supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Switch the power on and off.
The switch_binary1 channel supports the Switch item and is in the Switch category.
Provides start / stop control of blinds.
The blinds_control1 channel supports the Rollershutter item and is in the Blinds category.
Switch the power on and off.
The switch_binary2 channel supports the Switch item and is in the Switch category.
Provides start / stop control of blinds.
The blinds_control2 channel supports the Rollershutter item and is in the Blinds category.
The following table provides a summary of the 14 configuration parameters available in the ZMNHCD. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 10 | ALL ON/ALL OFF | Responds to commands ALL ON / ALL OFF from Main Controller |
| 40 | Power reporting in watts on power change | Power consumption change threshold for sending updates |
| 42 | Power reporting in Watts by time interval | Power reporting in Watts by time interval for Q1 or Q2 |
| 71 | Operating modes | Operation Mode (Shutter or Venetian) |
| 72 | Slats tilting full turn time | Slat full turn time in tenths of a second. |
| 73 | Slats position | Slats position after up/down movement. |
| 74 | Motor moving up/down time | Shutter motor moving time of complete opening or complete closing |
| 76 | Motor operation detection | Power threshold to be interpreted when motor reach the limit switch |
| 78 | Forced Shutter calibration | Enters calibration mode if set to 1 |
| 80 | Reporting to Controller | Defines if reporting regarding power level, etc is reported to controller. |
| 85 | Power consumption max delay time | Time delay for detecting motor errors |
| 90 | Relay delay time | Defines the minimum time delay between next motor movement |
| 110 | Temperature sensor offset settings | Adds or removes an offset from the measured temperature. |
| 120 | Digital temperature sensor reporting | Threshold for sending temperature change reports |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Responds to commands ALL ON / ALL OFF from Main Controller Module responds to commands ALL ON / ALL OFF that may be sent by the main controller or by other controller belonging to the system.
Available config. parameters (data type is 2 Byte DEC):
- default value 255
- 255 - ALL ON active, ALL OFF active.
- 0 - ALL ON is not active, ALL OFF is not active
- 1 - ALL ON is not active ALL OFF active
- 2 - ALL ON active ALL OFF is not active The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | 0 - ALL ON is not active ALL OFF is not active |
| 1 | 1 - ALL ON is not active ALL OFF active |
| 2 | 2 - ALL ON is not active ALL OFF is not active |
| 255 | 255 - ALL ON active, ALL OFF active |
The manufacturer defined default value is 255 (255 - ALL ON active, ALL OFF active).
This parameter has the configuration ID config_10_2 and is of type INTEGER.
Power consumption change threshold for sending updates Power report is send (push) only when actual power (in Watts) in real time changes for more than set percentage comparing to previous actual power in Watts, step is 1%.
Set value means percentage, set value from 0 – 100 = 0% - 100%. Available configuration parameters (data type is 1 Byte DEC):
- default value 1
- 0 - reporting disabled
- 1 - 100 = 1% - 100% Reporting enabled.
NOTE: if power changed is less than 1W, the report is not send (pushed), independent of percentage set. Values in the range 0 to 100 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_40_1 and is of type INTEGER.
Power reporting in Watts by time interval for Q1 or Q2 Set value means time interval (0 – 32767) in seconds, when power report is send. Available configuration parameters (data type is 2 Byte DEC):
- default value 300 = 300s
- 0 - Reporting Disabled
- 1 - 32767 = 1 second - 32767 seconds. Reporting enabled, power report is send with time interval set by entered value. Values in the range 0 to 32767 may be set.
The manufacturer defined default value is 300.
This parameter has the configuration ID config_42_2 and is of type INTEGER.
Operation Mode (Shutter or Venetian) This parameter defines selection between two available operating modes. Available configuration parameters (data type is 1 Byte DEC):
- default value 0
- 0 - Shutter mode
- 1 - venetian mode (up/down and slate rotation) NOTE1: After parameter change, first exclude module (without setting parameters to default value) then wait at least 30s and then re include the module! The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | 0 – Shutter mode |
| 1 | 1 – Venetian mode (up/down and slate rotation) |
The manufacturer defined default value is 0 (0 – Shutter mode).
This parameter has the configuration ID config_71_1 and is of type INTEGER.
Slat full turn time in tenths of a second. This parameter defines the time necessary for slats to make full turn (180 degrees). Available configuration parameters (data type is 2 Byte DEC):
- default value 150 = 1,5 seconds
- 0 - tilting time disabled
- 1 - 32767 = 0,01seconds - 327,67 seconds
NOTE: If time set is too high, this will result that after full turn, Shutter will start move up/down, for time remaining. Values in the range 0 to 32767 may be set.
The manufacturer defined default value is 150.
This parameter has the configuration ID config_72_2 and is of type INTEGER.
Slats position after up/down movement. This parameter defines slats position after up/down movement through Z-wave or push-buttons. Available configuration parameters (data type is 1 Byte DEC):
- default value 1
- 0 - Slats return to previously set position only in case of Z-wave control (not valid for limit switch positions).
- 1 - Slats return to previously set position in case of Z-wave control, push-button operation or when the lower limit switch is reached. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | 0 - return to previous position for Z-wave control only |
| 0 | |
| 1 | 1 - return to previous position in all cases |
The manufacturer defined default value is 1 (1 - return to previous position in all cases).
This parameter has the configuration ID config_73_1 and is of type INTEGER.
Shutter motor moving time of complete opening or complete closing This parameter defines Shutter motor moving time of complete opening or complete closing. Available configuration parameters (data type is 2 Byte DEC):
- default value 0
- 0 - moving time disabled (working with limit switches)
- 1 - 32767 = 0,1seconds - 3276,7seconds. After that time motor is stopped (relay goes to off state)
NOTE: Important is that the reference position to manually set moving time is always Shutter lower position!
Set parameter 74 to 0 and move the Shutter (using up/down push buttons or main controller UI) to the lowest desired position. On this Shutter position, set parameter 74 to time for complete opening or complete closing. At this point Shutter can be moved up (open) for set time, but can't be moved down because this position is already set as lower Shutter position.
To change Shutter lower position below already set (manual recalibration), parameter 74 must be set to 0 and repeat the procedure described above.
In case Shutter has limit switches, but anyhow you would like to limit opening/closing position by time, you can still do it. In case you put time that is longer that opening/closing real time limited by limit switches, Shutter will stop at limit switch, but the module relay will switch off after define time, not by Shutter limit switch. Take in consideration that in this condition, the positioning with slider through UI will not show correct Shutter position. NOTE that is not recommended using this for slates operation since its positioning can be compromised during time. Values in the range 0 to 32767 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_74_2 and is of type INTEGER.
Power threshold to be interpreted when motor reach the limit switch Power threshold to be interpreted when motor reach the limit switch. Available configuration parameters (data type is 1 Byte DEC):
- default value 10 = 10W
- 0 - 127 = 1-127 W. The value 0 means reaching a limit switch will not be detected
NOTE: Motors with power consumption less than 0,5W could not be auto calibrated. In that case set time manually (par. 74). Values in the range 0 to 127 may be set.
The manufacturer defined default value is 10.
This parameter has the configuration ID config_76_1 and is of type INTEGER.
Enters calibration mode if set to 1 By modifying the parameters setting from 0 to 1 a Shutter DC module enters the calibration mode. Available configuration parameters (data type is 1 Byte DEC):
- default value 0
- 1 - Start calibration process (when calibration process is finished, completing full cycle - up, down and up, set the parameter 78 (Forced Shutter calibration) value back to 0. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | 0 - Default |
| 1 | 1 - Start Calibration Process |
The manufacturer defined default value is 0 (0 - Default).
This parameter has the configuration ID config_78_1 and is of type INTEGER.
Defines if reporting regarding power level, etc is reported to controller. This parameter defines if reporting regarding power level, multilevel, etc,…is reported to controller or not. Available configuration parameters: default value 1
- 0 reporting to controller is disabled
- 1 reporting to controller The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | 0 - Reporting to Controller Disabled |
| 1 | 1 - Reporting to Controller Enabled |
The manufacturer defined default value is 1 (1 - Reporting to Controller Enabled).
This parameter has the configuration ID config_80_1 and is of type INTEGER.
Time delay for detecting motor errors This parameter defines the max time before motor power consumption is read after one of the relays is switched ON. If there is no power consumption during this max time (motor not connected, damaged or requires higher time to start, motor in end position,...) the relay will switch OFF. Time is defined by entering it manually. Available configuration parameters (data type is 1 Byte DEC):
- default value 8 = 800ms
- 3 - 50 = 0,3seconds - 5seconds (100ms resolution)
- 0 = time is set automatically Values in the range 0 to 50 may be set.
The manufacturer defined default value is 8.
This parameter has the configuration ID config_85_1 and is of type INTEGER.
Defines the minimum time delay between next motor movement This parameter defines the minimum time delay between next motor movement (minimum time between switching motor off and on again). Available configuration parameters (data type is 1 Byte DEC):
- default value 5 = 500ms
- 1 - 30 = 0,1seconds - 3seconds (100ms resolution) Values in the range 1 to 30 may be set.
The manufacturer defined default value is 5.
This parameter has the configuration ID config_90_1 and is of type INTEGER.
Adds or removes an offset from the measured temperature. Set value is added or subtracted to actual measured value by sensor. Available configuration parameters (data type is 2 Byte DEC):
- default value 32536
- 32536 - offset is 0.0C
- From 1 to 100 - value from 0.1 °C to 10.0 °C is added to actual measured temperature.
- From 1001 to 1100 - value from -0.1 °C to -10.0 °C is subtracted to actual measured temperature. Values in the range 1 to 32536 may be set.
The manufacturer defined default value is 32536.
This parameter has the configuration ID config_110_2 and is of type INTEGER.
Threshold for sending temperature change reports If digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter. Available configuration parameters (data type is 1 Byte DEC):
- Default value 5 = 0,5°C
- 0 - reporting disabled
- 1-127 = 0,1°C - 12,7°C, step is 0,1°C Values in the range 0 to 127 may be set.
The manufacturer defined default value is 5.
This parameter has the configuration ID config_120_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ZMNHCD supports 5 association groups.
Association group 1 supports 1 node.
Association group 2 supports 16 nodes.
Association group 3 supports 16 nodes.
Association group 4 supports 16 nodes.
Association group 5 supports 16 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V3 | |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V3 | |
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 | |
| COMMAND_CLASS_MARK_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V3 | |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V2 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 | |
| COMMAND_CLASS_MARK_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V3 | |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V2 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 | |
| COMMAND_CLASS_MARK_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.