| layout | title |
|---|---|
documentation |
ZMNHWD - ZWave |
{% include base.html %}
This describes the Z-Wave device ZMNHWD, manufactured by Goap with the thing type UID of qubino_zmnhwd_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The ZMNHWD supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Qubino Flush RGBW module controls RGB/RGBW strips and LED strips or bulbs and has 5 special scene effects. It can also control halogen lights and fans. Its extremely small size allows for easy installation behind wall sockets and switches. Controlled devices may be powered by 12 or 24 VDC.
Supported control types:
- Push button (monostable switch)
- Bistable switch
This should hopefully work with models ZMNHWD1-ZMNHWD8 (which work on different frequencies).
To include the device, press the service button 3 times within 2 seconds. The LED will turn green if the device was properly included.
The device supports auto inclusion: Install the device and connect the power. The auto inclusion function will be active for about 2 minutes.
To exclude the device, press the service button 3 times within 2 seconds. The green LED will blink if the device was properly included and the device will be reset to factory defaults.
The following table summarises the channels available for the ZMNHWD -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
| Color Control | color_color | color_color | ColorLight | Color |
| Color Temperature | color_temperature | color_temperature | ColorLight | Dimmer |
| Brightness 1 | switch_dimmer1 | switch_dimmer | DimmableLight | Dimmer |
| Brightness 2 | switch_dimmer2 | switch_dimmer | DimmableLight | Dimmer |
| Brightness 3 | switch_dimmer3 | switch_dimmer | DimmableLight | Dimmer |
| Brightness 4 | switch_dimmer4 | switch_dimmer | DimmableLight | Dimmer |
Switch the power on and off.
The switch_binary channel and is of type switch_binary and supports the Switch item and is in the Switch category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel and is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
The color channel allows to control the color of a light. It is also possible to dim values and switch the light on and off.
The color_color channel and is of type color_color and supports the Color item and is in the ColorLight category.
The color temperature channel allows to set the color temperature of a light from 0 (cold) to 100 (warm).
The color_temperature channel and is of type color_temperature and supports the Dimmer item and is in the ColorLight category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer1 channel and is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer2 channel and is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer3 channel and is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer4 channel and is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
The following table provides a summary of the 14 configuration parameters available in the ZMNHWD. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Input IN1 configuration | Input IN1 configuration |
| 2 | Input IN2 configuration | Input IN2 configuration |
| 3 | Input IN3 configuration | Input IN3 configuration |
| 4 | Input IN4 configuration | Input IN4 configuration |
| 5 | Auto scene mode set | Activation of the programmed scene changing color shades. |
| 6 | Auto Scene Mode | Duration between Colour change |
| 7 | Memorize device status at power cut | Device will be set to status memorized before power cut. |
| 8 | Automatic turning off output after set time | Automatic turning off output after set time |
| 9 | Automatic turning on output after set time | Automatic turning on output after set time |
| 10 | MAX dimming value | MAX dimming value |
| 11 | MIN dimming value | MIN dimming value |
| 12 | Dimming time (soft on/off) | Dimming time (soft on/off) |
| 13 | Dimming time when key pressed | Dimming time when key pressed |
| 14 | 4 Dimmers mode | 4 Dimmers mode |
Input IN1 configuration
The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | NORMAL mode – momentary switch type |
| 2 | NORMAL mode – toggle switch type |
| 3 | NORMAL mode – toggle with memory switch type |
| 4 | BRIGHTNESS mode – momentary switch type |
| 5 | BRIGHTNESS mode – toggle switch type |
| 6 | BRIGHTNESS mode – toggle with memory switch type |
| 7 | RAINBOW mode – momentary switch type |
| 8 | SCENE mode – momentary switch type |
| 9 | SCENE mode – toggle switch type |
| 10 | SCENE mode – toggle with memory switch type |
The manufacturer defined default value is 4 (BRIGHTNESS mode – momentary switch type).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Input IN2 configuration
The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | NORMAL mode – momentary switch type |
| 2 | NORMAL mode – toggle switch type |
| 3 | NORMAL mode – toggle with memory switch type |
| 4 | BRIGHTNESS mode – momentary switch type |
| 5 | BRIGHTNESS mode – toggle switch type |
| 6 | BRIGHTNESS mode – toggle with memory switch type |
| 7 | RAINBOW mode – momentary switch type |
| 8 | SCENE mode – momentary switch type |
| 9 | SCENE mode – toggle switch type |
| 10 | SCENE mode – toggle with memory switch type |
The manufacturer defined default value is 7 (RAINBOW mode – momentary switch type).
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Input IN3 configuration
The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | NORMAL mode – momentary switch type |
| 2 | NORMAL mode – toggle switch type |
| 3 | NORMAL mode – toggle with memory switch type |
| 4 | BRIGHTNESS mode – momentary switch type |
| 5 | BRIGHTNESS mode – toggle switch type |
| 6 | BRIGHTNESS mode – toggle with memory switch type |
| 7 | RAINBOW mode – momentary switch type |
| 8 | SCENE mode – momentary switch type |
| 9 | SCENE mode – toggle switch type |
| 10 | SCENE mode – toggle with memory switch type |
The manufacturer defined default value is 8 (SCENE mode – momentary switch type).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Input IN4 configuration
The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | NORMAL mode – momentary switch type |
| 2 | NORMAL mode – toggle switch type |
| 3 | NORMAL mode – toggle with memory switch type |
| 4 | BRIGHTNESS mode – momentary switch type |
| 5 | BRIGHTNESS mode – toggle switch type |
| 6 | BRIGHTNESS mode – toggle with memory switch type |
| 7 | RAINBOW mode – momentary switch type |
| 8 | SCENE mode – momentary switch type |
| 9 | SCENE mode – toggle switch type |
| 10 | SCENE mode – toggle with memory switch type |
The manufacturer defined default value is 1 (NORMAL mode – momentary switch type).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Activation of the programmed scene changing color shades.
The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | Ocean |
| 2 | Lightning |
| 3 | Rainbow |
| 4 | Snow |
| 5 | Romantic |
| 6 | Party scene |
The manufacturer defined default value is 1 (Ocean).
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Duration between Colour change
- 1-127 – delay duration is 1 sec to 127 sec
- 1001-1127 – delay duration is from 1 min to 127 min. This parameter has no effect on Lighting and Party Scene. Values in the range 1 to 1127 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_6_2 and is of type INTEGER.
Device will be set to status memorized before power cut.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Do not memorize |
| 1 | Memorize |
The manufacturer defined default value is 0 (Do not memorize).
This parameter has the configuration ID config_7_1 and is of type INTEGER.
Automatic turning off output after set time
- 0 – Auto OFF disabled
- 1 – 32536 = 1 second – 32536 seconds Auto OFF Values in the range 0 to 32536 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_8_2 and is of type INTEGER.
Automatic turning on output after set time
- 0 – Auto ON disabled
- 1 – 32536 = 1 second – 32536 seconds Auto ON Values in the range 0 to 32536 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_9_2 and is of type INTEGER.
MAX dimming value 2-99 = 2 % – 99 % Values in the range 2 to 99 may be set.
The manufacturer defined default value is 99.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
MIN dimming value 1-98 = 1 % – 98 % Values in the range 1 to 98 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_11_1 and is of type INTEGER.
Dimming time (soft on/off)
- Default value 10 = 1 s
- 5 – 25 = from 0.5 to 2.5 seconds Values in the range 5 to 25 may be set.
The manufacturer defined default value is 10.
This parameter has the configuration ID config_12_1 and is of type INTEGER.
Dimming time when key pressed 1 – 127 = from 1 to 127 seconds
NOTE: Dimming time depends also on Min and Max dimming value. Values in the range 1 to 127 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_13_1 and is of type INTEGER.
4 Dimmers mode NOTE: If the parameter no. 14 is enabled, parameter no. 1,2,3,4 has no effect.
NOTE: After parameter change, first exclude device (without setting parameters to default value) and then re include the device. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Four dimmers mode disabled |
| 1 | Four dimmers mode enabled – momentary switch type |
| 2 | Four dimmers mode enabled – toggle switch type |
| 3 | Four dimmers mode enabled – toggle with memory switch type |
The manufacturer defined default value is 0 (Four dimmers mode disabled).
This parameter has the configuration ID config_14_1 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ZMNHWD supports 1 association group.
The Module can be set 1 auto-report ID in Group 1.
The Module will send BASIC_REPORT to device associated in Group 1 when correspond Device is activated.
Association group 1 supports 1 node.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V2 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_COLOR_V2 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V2 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V2 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V2 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V2 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.