| layout | title |
|---|---|
documentation |
ZMNHZD - ZWave |
{% include base.html %}
This describes the Z-Wave device ZMNHZD, manufactured by Goap with the thing type UID of qubino_zmnhzd_00_000.
The device is in the category of Sensor, defining Device used to measure something.
The ZMNHZD supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Weather Station is used for measuring temperature, humidity, wind & rain properties and sending the measurement values to your Z-Wave network.The Weather Station can measure 10 different values: two sets of temperature/humidity sensors, wing gauge with 5 sensors (direction, velocity, wind gust, temperature and wind chill) and a rain sensor. With the use of the included Weather Station USB KEY all 10 values (end points) are sent and rendered in your home Z-Wave network. Qubino Weather Station Key is used for receiving Wireless data packages (from Thermo/ Hygro Sensor Ch1, Thermo/ Hygro Sensor Ch2, Rain Gauge, Wind Gauge) and sends it to the Z-Wave Controller. The Key is designed to be plugged into the USB Power Adapter. Module receives data for Temperature, Wind Chill, Velocity, Wind Gust, Wind Direction, Humidity, Rain Rate and Battery Level for each Sensor. It is designed to act as repeater in order to improve range and stability of Z-wave network.
Remote Weather Sensors The remote weather sensors include a thermo-hygrometer, anemometer (wind sensor) and rain sensor. All data collected by the sensors are transmitted to the Weather Station Key by wireless RF, with a range up to 100 meters (open area). The Weather station Key supports a maximum of 2 thermo-hygrometers, allowing 2 channels of temperature/humidity display (Ch1 and Ch2)
Connect module to USB Power Supply auto-inclusion (works for about 5 seconds after connected to power supply) or enable add/remove mode on main controller hold service button S between 1.5 and 4 seconds
NOTE: For auto-inclusion procedure, first set main controller into inclusion mode and then connect module to USB power supply.
Connect module to power supply enable add/remove mode on main controller, hold service button S between 4 seconds and 8 seconds By this function, all parameters of the module are set to default values and own ID is deleted.
If service button S hold more than 1.5 and less than 4 seconds module is excluded, but configuration parameters are not set to default values.
The following table summarises the channels available for the ZMNHZD -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Sensor (velocity) | sensor_velocity | sensor_velocity | Number | |
| Sensor (temperature) | sensor_temperature | sensor_temperature | Temperature | Number:Temperature |
| Sensor (relative humidity) | sensor_relhumidity | sensor_relhumidity | Humidity | Number |
| Sensor (direction) | sensor_direction | sensor_direction | Number | |
| Sensor (rain rate) | sensor_rainrate | sensor_rainrate | Humidity | Number |
| Battery Level | battery-level | Battery | Number | |
| Thermo/ Hygro Sensor Ch1 – Temperature | sensor_temperature1 | sensor_temperature | Temperature | Number:Temperature |
| Battery Level | battery-level | Battery | Number | |
| Wind Gauge – Direction | sensor_direction2 | sensor_direction | Number | |
| Battery Level | battery-level | Battery | Number | |
| Wind Gauge – Velocity | sensor_velocity3 | sensor_velocity | Number | |
| Battery Level | battery-level | Battery | Number | |
| Wind Gauge – Wind gust | sensor_velocity4 | sensor_velocity | Number | |
| Battery Level | battery-level | Battery | Number | |
| Wind Gauge – Temperature | sensor_temperature5 | sensor_temperature | Temperature | Number:Temperature |
| Battery Level | battery-level | Battery | Number | |
| Wind Gauge – Wind Chill | sensor_temperature6 | sensor_temperature | Temperature | Number:Temperature |
| Battery Level | battery-level | Battery | Number | |
| Rain Sensor | sensor_rainrate7 | sensor_rainrate | Humidity | Number |
| Battery Level | battery-level | Battery | Number | |
| Thermo/ Hygro Sensor Ch1 – Humidity | sensor_relhumidity8 | sensor_relhumidity | Humidity | Number |
| Battery Level | battery-level | Battery | Number | |
| Thermo/ Hygro Sensor Ch2 – Temperature | sensor_temperature9 | sensor_temperature | Temperature | Number:Temperature |
| Battery Level | battery-level | Battery | Number | |
| Thermo/ Hygro Sensor Ch2 – Humidity | sensor_relhumidity10 | sensor_relhumidity | Humidity | Number |
| Battery Level | battery-level | Battery | Number |
Indicates the current velocity.
The sensor_velocity channel and is of type sensor_velocity and supports the Number item. This is a read only channel so will only be updated following state changes from the device.
Indicates the current temperature.
The sensor_temperature channel and is of type sensor_temperature and supports the Number:Temperature item and is in the Temperature category.
Indicates the current relative humidity.
The sensor_relhumidity channel and is of type sensor_relhumidity and supports the Number item and is in the Humidity category. This is a read only channel so will only be updated following state changes from the device.
Indicates the direction.
The sensor_direction channel and is of type sensor_direction and supports the Number item. This is a read only channel so will only be updated following state changes from the device.
Indicates the current relative humidity.
The sensor_rainrate channel and is of type sensor_rainrate and supports the Number item and is in the Humidity category. This is a read only channel so will only be updated following state changes from the device.
Channel type information on this channel is not found.
Endpoint 1 receives Temperature data from Thermo/ Hygro Sensor on Channel 1. It is capable of receiving data in range of -199.0 °C and 199.0 °C. However, the operating temperature of the 433 MHz sensor is from -10 °C to 60 °C
Indicates the current temperature.
The sensor_temperature1 channel and is of type sensor_temperature and supports the Number:Temperature item and is in the Temperature category.
Channel type information on this channel is not found.
Endpoint 2 receives Direction data from Wind Gauge. The data is in range of 0.0° to 360.0°.
Indicates the direction.
The sensor_direction2 channel and is of type sensor_direction and supports the Number item. This is a read only channel so will only be updated following state changes from the device.
Channel type information on this channel is not found.
Endpoint 3 receives wind speed data from Wind Gauge. It is capable of receiving data in range of 0.00 m/s to 88.00 m/s.
Indicates the current velocity.
The sensor_velocity3 channel and is of type sensor_velocity and supports the Number item. This is a read only channel so will only be updated following state changes from the device.
Channel type information on this channel is not found.
Endpoint 4 receives wind speed data from Wind Gauge. It is capable of receiving data in range of 0.00 m/s to 88.00 m/s.
Indicates the current velocity.
The sensor_velocity4 channel and is of type sensor_velocity and supports the Number item. This is a read only channel so will only be updated following state changes from the device.
Channel type information on this channel is not found.
Endpoint 5 receives Temperature data from Wind Gauge. It is capable of receiving data in range of -199.0 °C and 199.0 °C. However, the operating temperature of the sensor is from -10 °C to 60 °C
Indicates the current temperature.
The sensor_temperature5 channel and is of type sensor_temperature and supports the Number:Temperature item and is in the Temperature category.
Channel type information on this channel is not found.
Endpoint 6 receives Temperature data from Wind Gauge. It is capable of receiving data in range of -199.0 °C and 199.0 °C. However, the operating temperature of the sensor is from -10 °C to 60 °C
Indicates the current temperature.
The sensor_temperature6 channel and is of type sensor_temperature and supports the Number:Temperature item and is in the Temperature category.
Channel type information on this channel is not found.
Endpoint 7 receives and calculates rain rate. The rain rate is in range of 0.00 mm/h and 300.00 mm/h
Indicates the current relative humidity.
The sensor_rainrate7 channel and is of type sensor_rainrate and supports the Number item and is in the Humidity category. This is a read only channel so will only be updated following state changes from the device.
Channel type information on this channel is not found.
Endpoint 8 receives Humidity data from Thermo/ Hygro Sensor on Channel 1. The data is in range of 0% and 100%
Indicates the current relative humidity.
The sensor_relhumidity8 channel and is of type sensor_relhumidity and supports the Number item and is in the Humidity category. This is a read only channel so will only be updated following state changes from the device.
Channel type information on this channel is not found.
Endpoint 9 receives Temperature data from Thermo/ Hygro Sensor on Channel 2. It is capable of receiving data in range of -199.0 °C and 199.0 °C. However, the operating temperature of the sensor is from -10 °C to 60 °C.
Indicates the current temperature.
The sensor_temperature9 channel and is of type sensor_temperature and supports the Number:Temperature item and is in the Temperature category.
Channel type information on this channel is not found.
Endpoint 10 receives Humidity data from Thermo/ Hygro Sensor on Channel 2. The data is in range of 0% and 100%.
Indicates the current relative humidity.
The sensor_relhumidity10 channel and is of type sensor_relhumidity and supports the Number item and is in the Humidity category. This is a read only channel so will only be updated following state changes from the device.
Channel type information on this channel is not found.
The following table provides a summary of the 16 configuration parameters available in the ZMNHZD. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Wind Gauge | Wind Gauge, Wind Gust Top Value |
| 2 | Rain Gauge | Rain Rate top value |
| 3 | Wind Gauge | Wind Gust |
| 4 | Rain Gauge | Rain Rate |
| 5 | End Point 1 | Unsolicited report |
| 6 | End Point 2 | Unsolicited report |
| 7 | End Point 3 | Unsolicited report |
| 8 | End Point 4 | Unsolicited report |
| 9 | End Point 5 | Unsolicited report |
| 10 | End Point 6 | Unsolicited report |
| 11 | End Point 7 | Unsolicited report |
| 12 | End Point 8 | Unsolicited report |
| 13 | End Point 9 | Unsolicited report |
| 14 | End Point 10 | Unsolicited report |
| 15 | Random ID enable | enables/disables random ID |
| 250 | Unsecure / Secure Inclusion | Unsecure / Secure Inclusion |
Wind Gauge, Wind Gust Top Value Wind Gauge, Wind Gust Top Value, if the Wind Gust is Higher than the Parameter Value, a device triggers an Association Values in the range 0 to 8800 may be set.
The manufacturer defined default value is 1000.
This parameter has the configuration ID config_1_2 and is of type INTEGER.
Rain Rate top value If the sensor Rain Rate is higher than the parameter value, a device triggers a association. Values in the range 0 to 30000 may be set.
The manufacturer defined default value is 200.
This parameter has the configuration ID config_2_2 and is of type INTEGER.
Wind Gust 0 - if the wind gauge is higher than the parameter No. 1 value, then a device sends basic set = 0x00
1 - if the wind gauge is higher than the parameter No. 1 value, then a device sends basic set =0xff Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Rain Rate 0 - if the rain amount is higher than the parameter No. 2 value, then a device sends basic set = 0x00
1 - if the rain amount is higher than the parameter No. 2 value, then a device sends basic set =0xff Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Unsolicited report 0 - Unsolicited report disabled
1 - Unsolicited report enabled Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Unsolicited report 0 - Unsolicited report disabled
1 - Unsolicited report enabled Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Unsolicited report 0 - Unsolicited report disabled
1 - Unsolicited report enabled Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_7_1 and is of type INTEGER.
Unsolicited report 0 - Unsolicited report disabled
1 - Unsolicited report enabled Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Unsolicited report 0 - Unsolicited report disabled
1 - Unsolicited report enabled Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_9_1 and is of type INTEGER.
Unsolicited report 0 - Unsolicited report disabled
1 - Unsolicited report enabled Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
Unsolicited report 0 - Unsolicited report disabled
1 - Unsolicited report enabled Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_11_1 and is of type INTEGER.
Unsolicited report 0 - Unsolicited report disabled
1 - Unsolicited report enabled Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_12_1 and is of type INTEGER.
Unsolicited report 0 - Unsolicited report disabled
1 - Unsolicited report enabled Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_13_1 and is of type INTEGER.
Unsolicited report 0 - Unsolicited report disabled
1 - Unsolicited report enabled Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_14_1 and is of type INTEGER.
enables/disables random ID If Random ID is disabled, the Weather Station USB Key can receive data from multiple 433 MHz Sensors on the same Channel. If the Random ID is enabled, the USB Key can receive data from only one sensor on the same channel. If the USB Key does not receive a data from a sensor on a specific channel for more than 2.5 hours, it clears the Random ID of the device and waits for a new ID. If you replace the batteries in the modules, the Random ID will change. If you want that the USB Key accept a module immediately, set the Parameter No. 15 to “0” and in the next step again to “1”. Values in the range 0 to 1 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_15_1 and is of type INTEGER.
Unsecure / Secure Inclusion
- default Value 0
- 0 – Unsecure Inclusion
- 1 – Secure Inclusion
The Weather Station Key supports both, the secure and unsecure inclusion. Even if the controller does not support security command classes, the Key could be included as unsecure and keep all the functionality. By default, the Key includes as unsecure. To include the Key as secure follow the procedure:
- Include the Key into the controller
- Set the parameter 250 to the value “1”
- Enable add/remove mode on main controller,
- Hold service button S between 1.5 and 4 seconds to exclude the module
- If the exclusion of the module was successful, the LED on the module starts blinking
- Unplug the module out of the power supply
- enable add/remove mode on main controller
- Plug the module into the power supply to star autoinclusion
- Now the module should be included as secure
The same procedure is to include the module as unsecure Values in the range 0 to 1 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_250_1 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ZMNHZD supports 3 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Reserved for the communication with the main controller
Association group 1 supports 1 node.
triggered when the wind gust of the wind gauge exceed the configuration parameter 1 value
Association group 2 supports 16 nodes.
triggered when the rain rate exceed the configuration parameter 2 value
Association group 3 supports 16 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5 | Linked to BASIC |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5 | Linked to BASIC |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5 | Linked to BASIC |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5 | Linked to BASIC |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5 | Linked to BASIC |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5 | Linked to BASIC |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5 | Linked to BASIC |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5 | Linked to BASIC |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5 | Linked to BASIC |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5 | Linked to BASIC |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5 | Linked to BASIC |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.