| layout | title |
|---|---|
documentation |
ZDMI 1870171 - ZWave |
{% include base.html %}
This describes the Z-Wave device ZDMI 1870171, manufactured by Somfy with the thing type UID of somfy_1870171_00_000.
The device is in the category of Blinds, defining Roller shutters, window blinds, etc..
The ZDMI 1870171 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
The Somfy Z-Wave Digital Motor Interface (ZDMI) is a Z-Wave routing device that resides as a node within a designated Z-Wave control network. It receives Z-Wave transmissions and converts them to motor control commands for Somfy’s Sonesse 50 ILT2 (AC) motor and Sonesse 30 RS485 (DC) motor. The interface also receives feedback information from these motors and distributes it to the Z-Wave network.
- Upon power-up, the INCLUSION LED will illuminate for five (5) seconds then turn off. When the LED turns off, press the SETUP button to verify motor movement.
- Select the inclusion command on your Z-Wave programmer or remote controller.
- Press the SETUP button to include the ZDMI in the network. Verify that the INCLUSION LED stays illuminated when the interface is included in the network.
- Select the exclusion command on your Z-Wave programmer or remote controller.
- Press the SETUP button to exclude the ZDMI from the network. Verify that the INCLUSION LED turns off.
The ZDMI interface can be operated by 3rd party automation, handheld and PC based controllers, or by manually by pressing the SETUP button. The following convention is used when operating from either 3rd party automation or controllers:
- Light ON = Window Covering UP, Light OFF = Window Covering DOWN.
- Light DIM & BRIGHTEN = Window Covering Opened Percentage where 0% = Window Covering CLOSED at its lower limit, and 100% = Window Covering OPEN at its upper limit.
- Lighting percentage values between 0% and 100% = 99 intermediate window covering positions.
The following table summarises the channels available for the ZDMI 1870171 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Switch | switch_binary | Switch | Switch |
| Dimmer | switch_dimmer | DimmableLight | Dimmer |
| Scene Number | scene_number | Number |
Switch the power on and off.
The switch_binary channel supports the Switch item and is in the Switch category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.
Triggers when a scene button is pressed.
The scene_number channel supports the Number item.
The device has no configuration parameters defined.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The device does not support associations.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V3 | |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_PROTECTION_V1 | |
| COMMAND_CLASS_HAIL_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.