| layout | title |
|---|---|
documentation |
Heatit Z Water - ZWave |
{% include base.html %}
This describes the Z-Wave device Heatit Z Water, manufactured by ThermoFloor with the thing type UID of thermofloor_zwater_00_000.
The device is in the category of HVAC, defining Air condition devices, Fans.
The Heatit Z Water supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
- The relay outputs may be used for controlling actuators/valves in a hydronic heating system
- May be used to control both 24V actuators and 230V actuators
- Can be used together with a Heatit Z-Temp sensor in each zone
- DIN rail mounting
- Works as a Z-Wave repeater
- Firmware updates (OTA)
- Available firmware versions (analog/digital inputs)
- Supports encryption mode: S0, S2 Access Control Class, S2 Authenticated Class, S2 Unauthenticated Class
Place your primary controller in Adding Mode by following the manufacturer’s instructions, then activate the add mode on the device by clicking the small button through the little hole, marked with the text “INCLUSION”, in front of the Heatit Z-Water regulator. The Adding Mode is indicated by Heatit Z-Water status LED is blinking until a timeout occurs after 10 seconds or if the module has been added to the Z-Wave network.
Place your primary controller in Remov Mode by following the manufacturer’s instructions, then activate the remove mode on the device by clicking the small button through the little hole, marked with the text “INCLUSION”, in front of the Heatit Z-Water regulator. The Remove Mode is indicated by Heatit Z-Water status LED is blinking until a timeout occurs after 10 seconds or if the module has been removed from the Z-Wave network.
Heatit Z-Water is a DIN-rail regulator for controlling hydronic heating. Heatit Z-Water is a module that clips right onto a DIN rail to add a variety of functions to your wireless Z-Wave network.
Heatit Z-Water is equipped with 10 relay outputs and it has 4 analog/digital inputs. The module can be power supplied from a 230V AC mains connection, and is able to deliver an output supply of 24V DC or 230V. Heatit Z-Water relay outputs are able to be freely controlled from the Z-Wave network, and can be used for several purposes, e.g. on/off control of light, control of valve actuators for an underfloor heating system, or control of other home automation systems.
Heatit Z-Water analog/digital inputs (different firmware versions) can be configured to work with different functionality and can be connected to potential free contacts, open-collector outputs, and will be able to control other Z-Wave devices; switches, dimmers, etc. Furthermore, the inputs can be used as a Scene Controller and send Central Scene notifications to the Z-Wave gateway.
It is possible to configure the level and the indication of the status indicator LED in the front of the Heatit Z-Water module.
The following table summarises the channels available for the Heatit Z Water -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Switch | switch_binary | Switch | Switch |
| Dimmer | switch_dimmer | DimmableLight | Dimmer |
| Binary Sensor | sensor_binary | Door | Switch |
| Switch 1 | switch_binary1 | Switch | Switch |
| Switch 2 | switch_binary2 | Switch | Switch |
| Switch 3 | switch_binary3 | Switch | Switch |
| Switch 4 | switch_binary4 | Switch | Switch |
| Switch 5 | switch_binary5 | Switch | Switch |
| Switch 6 | switch_binary6 | Switch | Switch |
| Switch 7 | switch_binary7 | Switch | Switch |
| Switch 8 | switch_binary8 | Switch | Switch |
| Switch 9 | switch_binary9 | Switch | Switch |
| Switch 10 | switch_binary10 | Switch | Switch |
| Sensor (temperature) 11 | sensor_temperature11 | Temperature | Number:Temperature |
| Sensor (temperature) 12 | sensor_temperature12 | Temperature | Number:Temperature |
| Sensor (temperature) 13 | sensor_temperature13 | Temperature | Number:Temperature |
| Sensor (temperature) 14 | sensor_temperature14 | Temperature | Number:Temperature |
Switch the power on and off.
The switch_binary channel supports the Switch item and is in the Switch category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel supports the Dimmer item and is in the DimmableLight category.
Indicates if a sensor has triggered.
The sensor_binary channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| ON | Triggered |
| OFF | Untriggered |
Switch the power on and off.
The switch_binary1 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary2 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary3 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary4 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary5 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary6 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary7 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary8 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary9 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary10 channel supports the Switch item and is in the Switch category.
Indicates the current temperature.
The sensor_temperature11 channel supports the Number:Temperature item and is in the Temperature category.
Indicates the current temperature.
The sensor_temperature12 channel supports the Number:Temperature item and is in the Temperature category.
Indicates the current temperature.
The sensor_temperature13 channel supports the Number:Temperature item and is in the Temperature category.
Indicates the current temperature.
The sensor_temperature14 channel supports the Number:Temperature item and is in the Temperature category.
The following table provides a summary of the 14 configuration parameters available in the Heatit Z Water. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Status LED | Configuration of the status LED |
| 2 | LED brightness | Configure the percentage of light in the status LED, when the LED is turned on |
| 3 | Thermistor type input 1 | This parameter decides which kind of thermistor that is connected to the input.. |
| 4 | Thermistor type input 2 | This parameter decides which kind of thermistor that is connected to the input. |
| 5 | Thermistor type input 3 | This parameter decides which kind of thermistor that is connected to the input. |
| 6 | Thermistor type input 4 | This parameter decides which kind of thermistor that is connected to the input. |
| 7 | Input 1 calibration | Input 1 calibration |
| 8 | Input 2 calibration | Input 1 calibratio2 |
| 9 | Input 3 calibration | Input 3 calibration |
| 10 | Input 4 calibration | Input 4 calibration |
| 11 | Input 1 report interval | Time interval between consecutive temperature reports. |
| 12 | Input 2 report interval | Time interval between consecutive temperature reports. |
| 13 | Input 3 report interval | Time interval between consecutive temperature reports. |
| 14 | Input 4 report interval | Time interval between consecutive temperature reports. |
Configuration of the status LED 0 LED turned off.
1 LED turned on. (Default)
2 LED flashing at 1 second intervals (½ Hz).
3 LED flashing at ½ second interval (1 Hz). The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | LED turned off. |
| 1 | LED turned on. (Default) |
| 2 | LED flashing at 1 second intervals (½ Hz) |
| 3 | LED flashing at ½ second interval (1 Hz) |
The manufacturer defined default value is 1 (LED turned on. (Default)).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Configure the percentage of light in the status LED, when the LED is turned on Specifies the brightness level of the LED when it is on. Default is 50. Values in the range 0 to 100 may be set.
The manufacturer defined default value is 50.
This parameter has the configuration ID config_2_1 and is of type INTEGER.
This parameter decides which kind of thermistor that is connected to the input.. 0 No thermistor, input is disabled. (Default)
1 10K NTC. (PART NUMBER: TT02-10KC3-93D-3000R-TPH) The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No thermistor, input is disabled. (Default) |
| 1 | 10K NTC. (PART NUMBER: TT02-10KC3-93D-3000R-TPH) |
The manufacturer defined default value is 0 (No thermistor, input is disabled. (Default)).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
This parameter decides which kind of thermistor that is connected to the input. 0 No thermistor, input is disabled. (Default)
1 10K NTC. (PART NUMBER: TT02-10KC3-93D-3000R-TPH) The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No thermistor, input is disabled. (Default) |
| 1 | 10K NTC. (PART NUMBER: TT02-10KC3-93D-3000R-TPH) |
The manufacturer defined default value is 0 (No thermistor, input is disabled. (Default)).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
This parameter decides which kind of thermistor that is connected to the input. 0 No thermistor, input is disabled. (Default)
1 10K NTC. (PART NUMBER: TT02-10KC3-93D-3000R-TPH) The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No thermistor, input is disabled. (Default) |
| 1 | 10K NTC. (PART NUMBER: TT02-10KC3-93D-3000R-TPH) |
The manufacturer defined default value is 0 (No thermistor, input is disabled. (Default)).
This parameter has the configuration ID config_5_1 and is of type INTEGER.
This parameter decides which kind of thermistor that is connected to the input. 0 No thermistor, input is disabled. (Default)
1 10K NTC. (PART NUMBER: TT02-10KC3-93D-3000R-TPH) The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No thermistor, input is disabled. (Default) |
| 1 | 10K NTC. (PART NUMBER: TT02-10KC3-93D-3000R-TPH) |
The manufacturer defined default value is 0 (No thermistor, input is disabled. (Default)).
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Input 1 calibration -4.0°C – 4.0°C. Default is 0 (0.0°C). Values in the range -40 to 40 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_7_1 and is of type INTEGER.
Input 1 calibratio2 -4.0°C – 4.0°C. Default is 0 (0.0°C). Values in the range -40 to 40 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Input 3 calibration -4.0°C – 4.0°C. Default is 0 (0.0°C). Values in the range -40 to 40 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_9_1 and is of type INTEGER.
Input 4 calibration -4.0°C – 4.0°C. Default is 0 (0.0°C). Values in the range -40 to 40 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
Time interval between consecutive temperature reports. 0 Reporting of temperatures disabled.
1 - 8640 Multiply with 10 seconds, 10 seconds – 24 hours. Default is 6 (60 seconds) The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Reporting of temperatures disabled. |
| 1 | Multiply with 10 seconds, 10 seconds – 24 hours. |
The manufacturer defined default value is 6.
This parameter has the configuration ID config_11_2 and is of type INTEGER.
Time interval between consecutive temperature reports. 0 Reporting of temperatures disabled.
1 - 8640 Multiply with 10 seconds, 10 seconds – 24 hours. Default is 6 (60 seconds). Values in the range 0 to 8640 may be set.
The manufacturer defined default value is 6.
This parameter has the configuration ID config_12_2 and is of type INTEGER.
Time interval between consecutive temperature reports. 0 Reporting of temperatures disabled.
1 - 8640 Multiply with 10 seconds, 10 seconds – 24 hours. Default is 6 (60 seconds). Values in the range 0 to 8640 may be set.
The manufacturer defined default value is 6.
This parameter has the configuration ID config_13_2 and is of type INTEGER.
Time interval between consecutive temperature reports. 0 Reporting of temperatures disabled.
1 - 8640 Multiply with 10 seconds, 10 seconds – 24 hours. Default is 6 (60 seconds). Values in the range 0 to 8640 may be set.
The manufacturer defined default value is 6.
This parameter has the configuration ID config_14_2 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The Heatit Z Water supports 14 association groups.
Main control device Lifeline.
Sends Device Reset notifications and Basic Report On / Off when relay output 1 is activated.
Max. nodes in the group: 5
Association group 1 supports 5 nodes.
Main control device Lifeline.
Sends Basic Report On / Off when relay output 2 is activated.
Max. nodes in the group: 5
Association group 2 supports 5 nodes.
Main control device Lifeline.
Sends Basic Report On / Off when relay output 3 is activated.
Max. nodes in the group: 5
Association group 3 supports 5 nodes.
Main control device Lifeline.
Sends Basic Report On / Off when relay output 4 is activated.
Max. nodes in the group: 5
Association group 4 supports 5 nodes.
Main control device Lifeline.
Sends Basic Report On / Off when relay output 5 is activated.
Max. nodes in the group: 5
Association group 5 supports 5 nodes.
Main control device Lifeline.
Sends Basic Report On / Off when relay output 6 is activated.
Max. nodes in the group: 5
Association group 6 supports 5 nodes.
Main control device Lifeline.
Sends Basic Report On / Off when relay output 7 is activated.
Max. nodes in the group: 5
Association group 7 supports 5 nodes.
Main control device Lifeline.
Sends Basic Report On / Off when relay output 8 is activated.
Max. nodes in the group: 5
Association group 8 supports 5 nodes.
Main control device Lifeline.
Sends Basic Report On / Off when relay output 9 is activated.
Max. nodes in the group: 5
Association group 9 supports 5 nodes.
Main control device Lifeline.
Sends Basic Report On / Off when relay output 10 is activated.
Max. nodes in the group: 5
Association group 10 supports 5 nodes.
Main control device Sends Multilevel Sensor Reports for input 1. Max. nodes in the group: 5
Association group 11 supports 5 nodes.
Main control device Sends Multilevel Sensor Reports for input 2. Max. nodes in the group: 5
Association group 12 supports 5 nodes.
Main control device Sends Multilevel Sensor Reports for input 3. Max. nodes in the group: 5
Association group 13 supports 5 nodes.
Main control device Sends Multilevel Sensor Reports for input 4. Max. nodes in the group: 5
Association group 14 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | |
| COMMAND_CLASS_SENSOR_BINARY_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 | |
| COMMAND_CLASS_SECURITY_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.