| layout | title |
|---|---|
documentation |
WiDom Universal Relay Switch - ZWave |
{% include base.html %}
This describes the Z-Wave device WiDom Universal Relay Switch, manufactured by wiDom with the thing type UID of widom_ubs_01_000.
This version of the device is limited to firmware version 1.0
The WiDom Universal Relay Switch supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
No device information is provided in the database. Consider updating the database to improve the documentation.
The following table summarises the channels available for the WiDom Universal Relay Switch -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Switch | switch_binary | Switch | Switch |
Switch the power on and off.
The switch_binary channel supports the Switch item and is in the Switch category.
The following table provides a summary of the 2 configuration parameters available in the WiDom Universal Relay Switch. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Device status 1 click | Device status when the external switch receives 1 click |
| 2 | Device status 2 click | |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Device status when the external switch receives 1 click
The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | TOGGLE |
| 2 | On |
| 3 | Off |
| 4 | IGNORE |
The manufacturer defined default value is 1 (TOGGLE).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Device status when the external switch receives 2 click The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | TOGGLE |
| 2 | On |
| 3 | Off |
| 4 | IGNORE |
The manufacturer defined default value is 1 (TOGGLE).
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The WiDom Universal Relay Switch supports 5 association groups.
Devices that will be notified of changes in its status
Association group 1 supports 16 nodes.
Devices that will be controlled by a single click on the external switch
Association group 2 supports 16 nodes.
Devices that will be controlled by a double click on the external switch
Association group 3 supports 16 nodes.
Devices that will be controlled by a triple click on the external switch
Association group 4 supports 16 nodes.
Devices that will be controlled by hold on the external switch
Association group 5 supports 16 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_NODE_NAMING_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.