| layout | title |
|---|---|
documentation |
ZW37 - ZWave |
{% include base.html %}
This describes the Z-Wave device ZW37, manufactured by Willis Electric Co., Ltd. with the thing type UID of willis_zw37_00_000.
The device is in the category of Power Outlet, defining Small devices to be plugged into a power socket in a wall which stick there.
The ZW37 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
- Follow the instructions for your Z-Wave certified controller to include the device to the Z-Wave network. 2. Once the controller is ready to include your device, single press and release the toggle (A) 3-5 times within 3 seconds on the device to include it in the network. * Devices with AUTO Inclusion - After setting the HUB controller to Inclusion/Pairing mode, simply plug in the device and the device will automatically begin the inclusion process. 3. Once your controller has confirmed that the device has been included and placed at its desired location, refresh the Z-Wave network to optimize performance. 4. The association group supports two nodes and life line function. Note: Your device may need to be within 10 feet of the controller to be included. If so, include the device to the network within 10 feet of the controller and relocate it to the desired position in your home. Be sure to refresh the network if the device is included in this manner.
- Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network. 2. Once the controller is ready to exclude your device, press in and release the toggle (A) 3-5 times within 3 seconds to exclude it from the network.
The following table summarises the channels available for the ZW37 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Switch | switch_binary | Switch | Switch |
| Switch 1 | switch_binary1 | Switch | Switch |
| Switch 2 | switch_binary2 | Switch | Switch |
Switch the power on and off.
The switch_binary channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary1 channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary2 channel supports the Switch item and is in the Switch category.
The device has no configuration parameters defined.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The device does not support associations.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.