| layout | title |
|---|---|
documentation |
YRD256 - ZWave |
{% include base.html %}
This describes the Z-Wave device YRD256, manufactured by ASSA ABLOY with the thing type UID of yale_yrd256_00_000.
The device is in the category of Lock, defining Devices whose primary pupose is locking something.
The YRD256 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
- Installs On Standard Doors In Minutes
- Replaces existing deadbolt with just a screwdriver
- Fits on doors 1 3/8" to 2 1/4" thick
- Backset 2 3/4" or 2 3/4"
- Face Bore Hole: 2 1/8"
- Edge Bore Hole: 1"
- Create up to 250 entry codes for access by keypad (when used with Network Module - 25 without)
To include the lock in a Z-Wave Network (taken from the installation manual:
- Touch the lock screen to activate
- Enter the master pin and press # Press 7, then # Press 1, then #
- The lock will now be in inclusion mode.
To exclude the lock from a Z-Wave Network (taken from the installation manual:
- Touch the lock screen to activate
- Enter the master pin and press # Press 7, then # Press 3, then #
- The lock will now be in exclusion mode.
The following table summarises the channels available for the YRD256 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Door Lock | lock_door | Door | Switch |
| Alarm (access) | alarm_access | Door | Switch |
| Alarm (power) | alarm_power | Door | Switch |
| Alarm (raw) | alarm_raw | String | |
| Battery Level | battery-level | Battery | Number |
| Clock Time Offset | time_offset | Temperature | Number |
Lock and unlock the door.
The lock_door channel supports the Switch item and is in the Door category.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| ON | Locked |
| OFF | Unlocked |
Indicates if the access control alarm is triggered.
The alarm_access channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Indicates if a power alarm is triggered.
The alarm_power channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Provides alarm parameters as json string.
The alarm_raw channel supports the String item. This is a read only channel so will only be updated following state changes from the device.
This channel sets, and provides the alarm state as a JSON string. It is designed for use in rules.
Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.
The battery-level channel supports the Number item and is in the Battery category.
Provides the current time difference for the devices time.
The time_offset channel supports the Number item and is in the Temperature category.
The following table provides a summary of the 7 configuration parameters available in the YRD256. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Volume | Volume of voice and beeps |
| 2 | Auto relock | Automatic relocking |
| 3 | Auto relock time | Time for auto relock |
| 4 | Incorrect PIN limit | Number of incorrect PINs before lockout |
| 6 | Radio event reporting | |
| 7 | Keypad lockout time | Incorrect PINs lockout time |
| 8 | Operation Mode | Operation Mode |
| Lock Timeout | Sets the time after which the door will auto lock |
Volume of voice and beeps
The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | Loud |
| 2 | Quiet |
| 3 | Silent |
The manufacturer defined default value is 1 (Loud).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Automatic relocking
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | No auto-relock |
| 255 | Auto relock |
The manufacturer defined default value is 0 (No auto-relock).
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Time for auto relock Number of seconds after the door is unlocked that it will attempt to automatically re-lock itself, if enabled. Values in the range 5 to 255 may be set.
The manufacturer defined default value is 30.
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Number of incorrect PINs before lockout Number of incorrect PINs that can be attempted before lock goes into temporary keypad lockout. Values in the range 1 to 7 may be set.
The manufacturer defined default value is 5.
This parameter has the configuration ID config_4_1 and is of type INTEGER.
This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Don't report events? |
| 255 | Do report events? |
The manufacturer defined default value is 255 (Do report events?).
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Incorrect PINs lockout time Amount of time to lock-out the keypad once the number of incorrect PINs has been reached on the keypad. (Zwave is still active during lockout.)This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 1 to 255 may be set.
The manufacturer defined default value is 60.
This parameter has the configuration ID config_7_1 and is of type INTEGER.
Operation Mode This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Normal |
| 1 | Vacation |
| 2 | Privacy |
| 3 | Disable Zwave |
The manufacturer defined default value is 0 (Normal).
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Sets the time after which the door will auto lock.
This parameter has the configuration ID doorlock_timeout and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The YRD256 supports 1 association group.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Association group 1 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_DOOR_LOCK_LOGGING_V1 | |
| COMMAND_CLASS_SCHEDULE_ENTRY_LOCK_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_DOOR_LOCK_V1 | |
| COMMAND_CLASS_USER_CODE_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V4 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_TIME_V1 | |
| COMMAND_CLASS_TIME_PARAMETERS_V1 | |
| COMMAND_CLASS_SECURITY_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.