Skip to content

Latest commit

 

History

History
116 lines (71 loc) · 4.38 KB

hmhs1cgz_0_0.md

File metadata and controls

116 lines (71 loc) · 4.38 KB
layout title
documentation
HM-HS1CG-Z - ZWave

{% include base.html %}

HM-HS1CG-Z Combustible Gas Sensor

This describes the Z-Wave device HM-HS1CG-Z, manufactured by Zipato with the thing type UID of zipato_hmhs1cgz_00_000.

The device is in the category of Sensor, defining Device used to measure something.

HM-HS1CG-Z product image

The HM-HS1CG-Z supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.

Overview

This Smart Combustible Gas Sensor adopts super low power consumption Z-Wave Wireless module. Used for detecting combusting gas leakage and preventing danger caused by gas leakage it also can be used as Z-Wave repealer to extend wireless transmission distance. It adopts high stability semi-conductor gas sensor. Sensor alarms if gas density in air exceeds set alarm level. It is applicable for kitchen or possible gas leakage in in-door area.

Inclusion Information

  • Click [Add] icon in Z-Wave Controller.
  • Press the Net_Button 3 times within 1.5s, Green LED is Blinking 3 times within 1 second.
  • If add Process is successful, Green LED will turn on

Exclusion Information

  • Click [Remove] icon in Z-Wave Controller.
  • Press the Net_Button 3 times within 1.5s
  • If remove Process is successful, Green LED is Blinking 6 times, then turn on

Channels

The following table summarises the channels available for the HM-HS1CG-Z -:

Channel Channel Id Category Item Type
Alarm alarm_general Door Switch

Alarm

Indicates if an alarm is triggered.

The alarm_general channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value Label
OFF OK
ON Alarm

Device Configuration

The device has no configuration parameters defined.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The HM-HS1CG-Z supports 2 association groups.

Group 1: Lifeline

The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.

  • Lifeline between controller and the device.
  • Supported command classes: Notification report, and Device Reset Locally notification.
  • Association Group description: Association group 1: Lifeline association group
  • Maximum supported node is 1.

Include command classes: Notification Report and Device Reset Locally notification.

Association group 1 supports 1 node.

Group 2: Root Device group(Notification)

Maximum supported nodes are 5.

1-Notification reports status of gas detected or no gas

    Association group 1: Lifeline association group

2-When the sensor detects status change of gas detected and no gas detected, the device will be triggered.

Association group 2 supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ALARM_V7
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1
COMMAND_CLASS_POWERLEVEL_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_VERSION_V2

Documentation Links

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.