| layout | title |
|---|---|
documentation |
ZEN26 - ZWave |
{% include base.html %}
This describes the Z-Wave device ZEN26, manufactured by Zooz with the thing type UID of zooz_zen26_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The ZEN26 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Manual or Z-Wave on/off control with instant status updates
Simple Direct 3-Way: connect with existing on/off switches in 3-way, 4-way, and 5-way set-ups, no add-on needed (neutral wire required)
Remembers and restores on/off status after power failure
LED indicator signals inclusion, exclusion, reset, and setting changes
Built-in Z-Wave Plus signal repeater to extend network range
Works with LED, CFL, and incandescent bulbs
S2 security protocol and the latest 500 Z-Wave chip for faster and safer wireless communication
Supported by most Z-Wave controllers
TAP Upper paddle 3-5 TIMES QUICKLY
The LED indicator will blink to signal communication and remain on for 2 seconds to confirm inclusion
Tap the lower paddle on the switch 3 times quickly
To complete factory reset process manually, tap-tap-tap’n’hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset. NOTE: All previously recorded activity and custom settings will be erased from the device’s memory
The following table summarises the channels available for the ZEN26 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Switch | switch_binary | Switch | Switch |
Switch the power on and off.
The switch_binary channel supports the Switch item and is in the Switch category.
The following table provides a summary of the 4 configuration parameters available in the ZEN26. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Paddle Control | Choose Paddle Functionality (Invert) |
| 2 | LED Indicator Control | Change behavior of the LED indicator |
| 3 | Auto Turn-Off Timer | enable the Auto Turn-Off Timer |
| 5 | On Off Status After Power Failure | Set the on off status for the switch after power failure. |
Choose Paddle Functionality (Invert) Choose if you want the upper paddle to turn the light on or turn the light off when tapped The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Top on, Bottom off |
| 1 | Top off, Bottom on |
The manufacturer defined default value is 0 (Top on, Bottom off).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Change behavior of the LED indicator Choose if you want the LED indicator to turn on when the switch (light) is on or off, or if you want it to remain on or off at all times
OR
6 x TAP PADDLE to change the LED indicator mode The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | LED on when switch off |
| 1 | LED on when switch on |
| 2 | LED off |
| 3 | LED on |
The manufacturer defined default value is 0 (LED on when switch off).
This parameter has the configuration ID config_2_1 and is of type INTEGER.
enable the Auto Turn-Off Timer Use this parameter to set the time which you want the switch to automatically turn off once it has been turned on. The number entered as value corresponds to the number of seconds. Values in the range 0 to 32768 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_3_2 and is of type INTEGER.
Set the on off status for the switch after power failure. Set the on off status for the switch after power failure. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Off |
| 1 | On |
| 2 | last state |
The manufacturer defined default value is 2 (last state).
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ZEN26 supports 2 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. This device will send BINARY SWITCH REPORT to Group 1 and 2 when operated manually
Association group 1 supports 1 node.
This device will send BINARY SWITCH REPORT to Group 1 and 2 when operated manually
Association group 2 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.